Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
The hub bores d1 H7 are not provided for in the official standard sheet.
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...show more
Stainless steel indexing plungers GN 617 are designed such that the plunger set in the end position (pressure spring is "on block") can also absorb axial forces. For...show more
Rubber buffers GN 451 are suitable for the elastic mounting of machine units such as motors, compressors and pumps.
Angle pieces and shackles GN 967 are preferably used in connection with profile systems. Square connections or connections with same contact area can so be realised in the...show more
Adjustable tension levers GN 213.3 have proved to be ideal whenever parts have to be clamped in a confined space or a particular lever position is required. The threaded insert...show more
Adjustable hand levers GN 300.2 are ideal whenever parts have to be clamped in a confined space or in a particular lever position. The centre insert is connected to the lever...show more
Adjustable hand levers GN 302.2 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in...show more
Item-no.
1480279
Supplier number
600-63-M8-30-DBL
EAN
4045525101685
Quantity
1 Piece
Control knobs with adjustable spindle GN 727 allow precise adjustment or aligning i. e. of a positive stop. The spindle thread is without backlash. The graduations on the...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
The clamping bores of T-angle connector clamps GN 191 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Winkel GN 30b befestigen Aluprofile z. B. an Tischen und Platten oder rechtwinklig aneinander. Dabei ist keine Bearbeitung des Profils nötig. Die Verbindung lässt sich längs der...show more
Stainless ateel angled ball joints DIN 71802 consist of a ball socket DIN 71805 and a ball shank DIN 71803. The angle of rotation for the type with safety catch (Type CSN) is...show more
The official DIN standard sheet specifies additional sizes 200 - M24 / B24.
Cabinet U-handles GN 425.1 are manufactured from a bent stainless steel profile. Cabinet U-handles with Ø d1 = 8 and 10 are delivered with two location disks to ensure proper...show more
Construction tubes GN 990 can be supplied in these standard lengths. The tolerances specified for the outside diameter of the round construction tubes comply with the...show more
The specified load in the above table is a recommendation up to which the damping insert can be permanently subjected. This static load equals a thrust on the area of 0,4 N/mm2,...show more
Leveling feet GN 343.8 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more
Assembly tools GN 355.1 serve to adjust leveling elements GN 355 / GN 355.2. They are used in connection with a T-wrench or a hexagonal angle socket spanner. To ease leveling,...show more
Item-no.
1218728
Supplier number
1130-8-10-ST
EAN
4045525914148
Quantity
1 Piece
Ball chains GN 111.5 are mainly used in connection with ball lock pins and pins with axial lock. The key rings are supplied unmounted. Both rings have the same Ø d1. The load...show more