The clamping bore of base plate connector clamps GN 165 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...show more
Base plate mounting clamps GN 473 have a horizontal and a vertical clamping bore. The vertical clamping bore is additionally fitted with a square. The bore distance m...show more
Foot plates GN 6311.3 are used in connection with screws with pivots (grub screws DIN 6332, tommy screws DIN 6304, DIN 6306) for installing and leveling devices and mechanisms....show more
Fork joints GN 751 consists of a fork head according to DIN 71752 and a pin with one safety circlip DIN 471 (typeA). Standard DIN 71752 does not foresee size d1 = 20.
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
Knurled handwheels GN 226 are mainly used instead of star and hand knobs for light adjusting or clamping applications.
Grub screws GN 632.1 with ball point are as a rule used with thrust pads GN 631. The ball Ø d2 is smaller than the thread core Ø, which allows fitting over the ball end. The...show more
Stainless steel grub screws GN 632.5 with ball point are as a rule used with thrust pads GN 631 / GN 631.5. The ball Ø d2 is smaller than the thread core Ø, which allows fitting...show more
Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
The thrust point of the grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller than the core...show more
Item-no.
1200984
Supplier number
351-20-20-M6-EE-40
EAN
4045525599031
Quantity
1 Piece
Item-no.
1201135
Supplier number
351-75-40-M12-EE-40
EAN
4045525599208
Quantity
1 Piece
Rubber buffers GN 451 are suitable for the elastic mounting of machine units such as motors, compressors and pumps.
Item-no.
1348150
Supplier number
351-125-55-M16-ES-40
EAN
4045525028920
Quantity
1 Piece
Magnets GN 53.1 work in combination with the flat, disk-shaped plastic housing as a system for holding documents, templates, drawings etc. that are used in technical...show more
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Handles GN 810.15 are accessory for knee lever modules GN 810.12 / GN 810.13.
Cabinet U-handles GN 565.3 are manufactured from a bent aluminum profile. They are suitable for applications where lower lifting forces are required such as on lids or...show more
Item-no.
1352521
Supplier number
730.5-A4-120-GS
EAN
4045525131422
Quantity
1 Piece
Item-no.
1350663
Supplier number
520.1-150-K14-D
EAN
4045525097650
Quantity
1 Piece
Spoked Handwheels, Black, Powder Coated
The handle in the handwheels GN 322.3 is locked in a conical bore in the operating position. For reversal, it must first be pulled from the cone in axial direction. A pressure...show more
Heavy duty hinges GN 237.3 are designed for use under tough conditions and are distinguished by a compact design. The hinge pins are integral and allow the hinges to be used in...show more