Telescopic linear slides GN 2404 are used, for example, for storage drawers and sliding doors, or in jigmaking for a sliding motion in a linear direction. If the support screw...show more
Telescopic slides GN 1408 are installed vertically and in pairs. The stroke reaches ≈ 100 % of the nominal length l1 (full extension). The telescopic slides are delivered in...show more
Telescopic slides GN 1420 are installed vertically and in pairs. The stroke reaches ≈ 100 % of the nominal length l1 (full extension). The rubber stops of type E dampen the...show more
Countersunk washers GN 184.5 are retained to the face of the shaft end with a countersunk head screw DIN ISO 2009 or DIN 7991 forming a clean-look end cap. A typical application...show more
Studs GN 1050.1 position and attach components without tools using quick release couplings GN 1050 for a tight and repeatable fit. The dimensions and material properties of the...show more
Toggle latches GN 761 are especially suited for rapid closing and fastening of covers, container lids and boxes. When the lever is closed, the eccentric configuration of the rod...show more
Toggle latches GN 832 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Toggle latches GN 832.1are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Toggle latches GN 832.2are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Toggle latches GN 832.3 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
The thrust point of these screws DIN 6304 is designed to be used with or without a thrust pad for clamping. The snap ring is a simple and quick method to connect the thrust pad...show more
Guide rollers GN 753 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. With the radial...show more
Guide rollers GN 753.1 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. The radial load...show more
Transportrollen GN 22892 werden in industriellen und öffentlichen Innen-bereichen beispielsweise zum Verschieben von leichten Wagen eingesetzt. Der Laufbelag der Räder bewirkt...show more
Trapezgewindemuttern GN 103.3 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Je nach Werkstoff und der daraus resultierenden Festigkeit werden die Muttern in...show more
Item-no.
1723478
Supplier number
103.3-16X4-LH-1-ST
EAN
4045525948839
Quantity
1 Piece
Stainless steel triangular knobs GN 5339.5 have been specially designed for use on machinery in the food industry. The smooth and enclosed areas as well as the corner radii...show more
Cabinet U-handles GN 426.3 are manufactured from a bent steel profile.
Item-no.
1197013
Supplier number
333-28-500-A-SW
EAN
4045525193413
Quantity
1 Piece
The handle tube of the GN 333.1 tubular handles can be screwed to the handle bases without further machining or processing, allowing special lengths to be realised easily....show more
Item-no.
1484813
Supplier number
528.2-PA-150-SW
EAN
4045525707764
Quantity
1 Piece
Universal connectors GN 22i fasten aluminum profiles together at right angles and, when used in pairs, secure them against twisting. Only one profile has to be machined. The...show more
Toggle clamps GN 812 work according to the toggle principle: lever and clamping bar move in the same direction. They can be mounted in two planes via the dual flanged mounting...show more
Toggle clamps GN 810.3 are latched in both end positions. In the clamped position, this prevents unintentional opening or opening caused by vibrations, and in the open position,...show more