Typical in design are the retractable handles GN 798.5 with their stepped shape consisting of two cylinders giving the operator a better grip, especially when pulling the handle...show more
Clamping Levers, Stainless Steel
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks to the material used, the spherical washers and dished...show more
Telescopic slides GN 1408 are installed vertically and in pairs. The stroke reaches ≈ 100 % of the nominal length l1 (full extension). The telescopic slides are delivered in...show more
Countersunk washers GN 184.5 are retained to the face of the shaft end with a countersunk head screw DIN ISO 2009 or DIN 7991 forming a clean-look end cap. A typical application...show more
Toggle latches GN 833 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Plates GN 2372 are designed as accessories for multiple families of hinges with dimensions that make additional threaded holes, nuts and washers unnecessary for mounting. This...show more
Spring plungers GN 615.4 are used as detents as well as for push-on and push-off applications and ejectors.
Guide rollers GN 753 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. With the radial...show more
Guide rollers GN 753.1 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. The radial load...show more
Item-no.
1834505
Supplier number
22882-80-G-R-L-ST
EAN
4063632043896
Quantity
1 Piece
Item-no.
1834570
Supplier number
22885-100-K-R-L-ST
EAN
4063632042141
Quantity
1 Piece
Trapezgewindemuttern GN 103.2 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Die Schlüsselflächen dienen dabei der Befestigung und verhindern das Mitdrehen der...show more
Trapezgewindemuttern GN 103.3 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Je nach Werkstoff und der daraus resultierenden Festigkeit werden die Muttern in...show more
Item-no.
1722683
Supplier number
103-16X4-1000-RH-NI
EAN
4045525954427
Quantity
1 Piece
Trapezgewindespindeln GN 103 wandeln in Verbindung mit Trapezgewindemuttern Drehbewegungen in lineare Bewegungen um. Sie werden eingesetzt, wenn Bauteile bewegt und Kräfte...show more
Stainless steel triangular knobs GN 5339.5 have been specially designed for use on machinery in the food industry. The smooth and enclosed areas as well as the corner radii...show more
The handle tube of the GN 333.1 tubular handles can be screwed to the handle bases without further machining or processing, allowing special lengths to be realised easily....show more
The permissible r.p.m. of universal joints with friction bearing DIN 808 is to a large extent dependent on the type of application such as load, duration, angular disposition as...show more
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...show more
Threaded plugs DIN 906 are used to close bore holes with cylindrical internal thread. The tightness depends on the medium, pressure, temperature and material pairing. The design...show more
Toggle clamps GN 810.3 are latched in both end positions. In the clamped position, this prevents unintentional opening or opening caused by vibrations, and in the open position,...show more
Toggle clamps GN 813 are used for applications where a very high holding force is required, such as closing of foam molds. These clamps have been designed for easy dismantling:...show more
Toggle clamps GN 810.3 are latched in both end positions. In the clamped position, this prevents unintentional opening or opening caused by vibrations, and in the open position,...show more