Retractable handles GN 598.5 are used when the handle should not protrude temporarily for space or safety reasons.
Domed gear knobs GN 719.2 are very often used in place of ball knobs DIN 319 on switch levers, gear levers etc. Domed gear knobs satisfy by their form and ergonomical aspects....show more
T-handle screws GN 563.1 can be used on operating levers as well as on clamping fixtures. These handles lend themselves ideally for very high manual clamping forces.
T-handles GN 563 can be used on operating handles as well as on clamping fixtures. These handles lend themselves ideally for very high manual clamping forces.
Mushroom shaped knobs GN 75.5 have a compact and timeless design. Their non-scooping geometry combats dirt build-up and makes cleaning easier. Mushroom shaped knobs GN 75.5 can...show more
The design of the ball handles with threaded stud GN 675 matches the product family Ergostyle®. The Softline coating makes the control knobs particularly user-friendly and...show more
The design of the ball handles GN 675 matches the product family of the Ergostyle®. The Softline coating makes the control knobs particularly user-friendly and ergonomic. The...show more
The design of the ball handles GN 675.1 matches the product family Ergostyle®. The softline coating makes the control knobs particularly user-friendly and ergonomic. The soft,...show more
The ball knobs GN 319.1 do not require a thread at the shaft. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place, the shaft end should be...show more
Revolving ball knobs GN 319.2 are in general used where a pulling action is involved such as on vertically positioned handwheels.
Revolving ball knobs GN 319.5 are in general used where a "pulling action" is involved such as on vertically positioned handwheels.
Mushroom shaped knobs GN 75 have a compact and timeless design. Their non-scooping geometry combats dirt build-up and makes cleaning easier. Mushroom shaped knobs GN 75 in steel...show more
Mushroom shaped knobs GN 75.6 are intended for use in hygienic areas. The sealed mounting surface enables mounting without dead spaces, the impervious geometry in combination...show more
The tapered knobs GN 518 do not require a thread at the shaft. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place, the shaft end should...show more
When using the tapered knobs GN 219, make sure that the threaded pin is sufficiently long. Otherwise the plastic element may break under excessive stress exposure.
The Softline coating makes the cylindrical knobs GN 519.6 particularly user-friendly and ergonomic. The soft, antislip contact area improves the contact both in hot (hand...show more
The outstanding feature of revolving handles GN 598.2 is their highly robust design. Type E is suitable for use in connection with user-specific threaded bolts.
Typical in design are the revolving handles GN 798.1 with their stepped shape consisting of two cylinders giving the operator a better grip.
Cylindrical handles GN 539.2 are used as handles for electronic tools such as angle grinders, percussion drills etc. Their special feature is the hand guard on one or both sides.
The cylindrical knobs GN 519.1 do not require a thread at the shaft. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place, the shaft end...show more
Cylindrical knobs GN 519.2 are an advanced development of the Duroplast cylindrical knobs GN 519. Thanks to the polyamide material used in their manufacture, they feature superb...
Cylindrical handles GN 519.2 are made of blue plastic granulate that is FDA compliant as per FDA CFR.21 and EU 10/2011 as well as visually detectable or metal detectable. The...show more
Cylindrical knobs GN 519.2 are manufactured from an antimicrobial plastic. Adding a silver-based substance has created a natural active agent that helps to prevent the growth of...show more