Tube end plugs GN 991 have been designed for sealing tube ends for safety or optical reasons. They are pressed into the tube end either by hand or with a mallet.
For mounting clamps, the clamping kits GN 511 replace the socket cap screws with hexagonal socket DIN 912. It is used on all clamping points where repeated clamping actions are...show more
The dimensions of stainless steel retaining rods GN 480.3 are tailored for use with mounting clamps. The angled stainless steel retaining rods make it possible to create compact...show more
Swivel clamp connector joints GN 281 are an assembly of the swivel clamp connectors GN 271 and GN 275. The clamping bore is mechanically machined and designed for construction...show more
The clamping bores of two-way connector clamps GN 131 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
The clamping bores of two-way connector clamps GN 131 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Item-no.
1485151
Supplier number
911-63-M8-30-SR
EAN
4045525728547
Quantity
1 Piece
Angle pieces and shackles GN 967 are preferably used in connection with profile systems. Square connections or connections with same contact area can so be realised in the...show more
The clamping bores of T-angle connector clamps GN 191 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Winkel GN 30b befestigen Aluprofile z. B. an Tischen und Platten oder rechtwinklig aneinander. Dabei ist keine Bearbeitung des Profils nötig. Die Verbindung lässt sich längs der...show more
Clamping plates GN 9734 are used to fix the spindles of configurable linear actuators in place after adjustment. Using a hand lever, the bore diamter of the clamping plate is...show more
The clamping bores of two-way connector clamps GN 134 are not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 . The versions with square...show more
Two-Way Mounting Clamps, Plastic
The clamping bore of flanged connector clamps GN 147 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...show more
Base plate mounting clamps GN 473 have a horizontal and a vertical clamping bore. The vertical clamping bore is additionally fitted with a square. The bore distance m...show more
In addition to the standard travel lengths specified in the above table for the double tube linear actuator GN 491 any length inside the maximum travel length is available. In...show more
The clamping bore of swivel clamp connectors GN 276 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw location...show more
The clamping bore of tube supports GN 231 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Tube supports GN 231 can also be mounted...show more
The clamping bore of tube connectors GN 241 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square bores are...show more
Adjustable hand levers GN 911.3 replace the socket cap screws DIN 912 or the cap nuts DIN 917 of the tube clamp connectors and linear actuator connectors in stainless steel. The...show more
Flanged linear actuator connectors GN 146.13 are based on flanged connector clamps. The additionally provided mounting holes are used to connect to the drive key of a linear...show more
Swivel ball joint mounting clamps GN 487 allow precise and stepless adjustment of the ball pivot within the swivel range. This makes it easy to position and adjust components...show more
The clamping bore axes of the two-way connector clamps GN 132.9 are arranged at an angle of 90° to each other. They hold typical construction tubes with full surface contact...show more