Latches GN 119 lock by a turning operation clockwise (right), which moves the cam latch into the locked position behind the door frame. The latches have a pulling-in range of 10...Meer tonen
Art.-Nr.
1206324
Leveranciersnummer
598-KT-18-M6
EAN
4045525298514
Aantal
1 stuk
Art.-Nr.
1075654
Leveranciersnummer
598-KT-23-M8
EAN
4045525298576
VPE (Verpakking)
10 stuk
Aantal
1 stuk
Art.-Nr.
1206343
Leveranciersnummer
598-ST-26-M8
EAN
4045525298873
Aantal
1 stuk
Typical in design are the revolving handles GN 798.2 with their stepped shape consisting of two cylinders giving the operator a better grip.
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...Meer tonen
Control knobs GN 526 have a colored cover that conceals protruding or recessed shafts and is suitable for imprinting characters or symbols, if desired. For assembly, the cover...Meer tonen
The underside of the three-lobed knob screws GN 5342 is not recessed, which meets the requirements of a "hygienic" version.
Snap latches GN 449.4 combine the function of a gripping tray with that of a snap latch to provide an easy way to keep doors and covers closed. The mounting hole must be created...Meer tonen
The two hexagon nuts are included parts of the order.
By means of the retaining ring in the thrust pad a simple and toggle link between screw and thrust pad is created. The two hexagon nuts are included parts of the order.
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting connection between the thrust pin and thrust pad, they adapt...Meer tonen
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended.
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
Spring plungers GN 615.9 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable, which enables...Meer tonen
Stainless steel spring plungers GN 616 are used as detents as well as for push-on and push-off applications and ejectors. The slot on the plunger side is provided for blind hole...Meer tonen
Spring plungers GN 615.4 are used as detents as well as for push-on and push-off applications and ejectors.
Holders for spring plungers GN 614.1 are standard parts which simplify the use of spring plungers GN 614. Types R, L and B consist only of the holder for spring plungers...Meer tonen
Push-pull type toggle clamps GN 840 are known for their extremely low height regardless of the position of the operating handle.
Push-pull type toggle clamps GN 842 can be used for very high holding capacities thanks to their massive and sturdy body. On the size 70, the mounting holes are provided with...Meer tonen
Push-pull type toggle clamps GN 843.1 can be mounted on a mounting bracket (type ASW) or „directly“ on the jig. The center bushing securing method allows the operating handle to...Meer tonen
Hand knobs DIN 6335 with bore H7 are available as GN 6335.1. The size 100 is not on the official DIN standard sheet.
Elastomer jaw couplings GN 2240 can transmit very high torques while compensating for shaft misalignments and runout tolerances. They are preferred in applications where the...Meer tonen
Clamping levers with eccentrical cam GN 927 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen