The thrust point of these screws DIN 6304 is designed to be used with or without a thrust pad for clamping. The snap ring is a simple and quick method to connect the thrust pad...Meer tonen
Ball lock pins GN 113.9 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is location pins which have to be often removed...Meer tonen
The clamping nut of the ball joints GN 782 can be set to give a required thrust on the Belleville spring washers in order to increase the resistance to the ball movement. At the...Meer tonen
On the official DIN standard sheet you can find the additional sizes 10 and 13. For reasons of hygiene, no internal hexagon is used in type A4.
Ball chains GN 111.5 are mainly used in connection with ball lock pins and pins with axial lock. The key rings are supplied unmounted. Both rings have the same Ø d1. The load...Meer tonen
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...Meer tonen
Ball knobs DIN 319 made of steel and aluminum are not on the official DIN standard sheet.
Ball knobs DIN 319 are not on the official DIN standard sheet.
Ball Knobs, Plastic with Brass Insert
Art.-Nr.
1218728
Leveranciersnummer
1130-8-10-ST
EAN
4045525914148
Aantal
1 stuk
Ball lock pins GN 113.5 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...Meer tonen
Ball lock pins GN 113.8 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...Meer tonen
Ball lock pins GN 113.12 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...Meer tonen
Art.-Nr.
1211327
Leveranciersnummer
705-18-E-ZB
EAN
4045525828391
VPE (Verpakking)
10 stuk
Aantal
1 stuk
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
In the standard version, the clamping screws are socket cap screws with hexagonal socket DIN 912. They can be replaced by clamping kits GN 511 (article code see table of...
Twistable two-way mounting clamps GN 475 connect rods and tubes within the mounting clamp system under any adjustable angle. With the angle adjustment released, the mounting...Meer tonen
The clamping bores of two-way connector clamps GN 131 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
The clamping bores of two-way connector clamps GN 134 are not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 . The versions with square...Meer tonen
The permissible r.p.m. of universal joints with friction bearing DIN 808 is to a large extent dependent on the type of application such as load, duration, angular disposition as...Meer tonen
Universal joints GN 9080 are a simple and very competitively priced variant. They can only be used for applications with low revolutions. Typical applications are all types of...Meer tonen
Art.-Nr.
1209384
Leveranciersnummer
6335.4-SK-32-M6-30
EAN
4045525332140
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Bearing blocks GN 828 are used in combination with adjusting screws GN 827 for simple adjustment and positioning tasks. For processing and assembly equipment on which...Meer tonen