Screw-on spirit levels GN 2283 are used to check the horizontal position of jigs, machines, devices, appliances and instruments. The spirit levels of type AV are aligned in...Meer tonen
Flanged linear actuator connectors GN 146.13 are based on flanged connector clamps. The additionally provided mounting holes are used to connect to the drive key of a linear...Meer tonen
Retaining magnets GN 50.6 are combined with the steel housing and the plastic ring into a system that shields and strengthens the magnet for optimal transmission of the magnetic...
The retaining magnets GN 51.9 with rubber jacket form a system together with the steel part that shields and strengthens the magnet, optimally concentrating the magnetic flux on...Meer tonen
Magnets GN 53.4 work in combination with the ergonomic nickel-plated steel handle as a system for holding documents, templates, drawings etc. that are used in technical...Meer tonen
Magnetic bands GN 7110.2 are designed as accessories for magnetic measuring systems GN 7110 and are fastened using adhesive strips. They consist of two separate parts, the...Meer tonen
Retaining magnets GN 5090 are designed for use in hygienic areas. The sealed screw-on surface enables mounting without dead spaces, the impervious geometry in combination with...Meer tonen
Magnetic plugs GN 738 attract iron particles which might be suspended in the liquid. To avoid breakage or de-magnetising, round rod magnets are fitted with a plastic distance...Meer tonen
Mini indexing plungers GN 822.6 are distinguished for their small dimensions. Based on the principle of the GN 822 mini indexing plungers, this model combines their clever type...Meer tonen
Stainless steel mini indexing plungers GN 822.7 are distinguished for their small dimensions. Based on the principle of the mini indexing plungers GN 822, this model combines...Meer tonen
Mini indexing plungers GN 822.7 are distinguished for their small dimensions. Based on the principle of the mini indexing plungers GN 822, this model combines their clever type...Meer tonen
Mini indexing plungers GN 822.8 are distinguished for their small dimensions. They are mounted by countersunk screws. The mini indexing plungers present an affordable...Meer tonen
Mini indexing plungers GN 822.1 are distinguished for their small dimensions. They have been designed for installation in thin walled sheet metal constructions. In type C, the...Meer tonen
Stainless steel T-nuts DIN 508 are also available without thread. They can be adapted for special applications in this way.
With their smaller dimensions, thin hex nuts GN 909 expand the mounting options of indexing plungers and cam action indexing plungers.
Trapezgewindemuttern GN 103.2 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Die Schlüsselflächen dienen dabei der Befestigung und verhindern das Mitdrehen der...Meer tonen
Trapezgewindemuttern GN 103.3 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Je nach Werkstoff und der daraus resultierenden Festigkeit werden die Muttern in...Meer tonen
Assembly tools GN 355.1 serve to adjust leveling elements GN 355 / GN 355.2. They are used in connection with a T-wrench or a hexagonal angle socket spanner. To ease leveling,...Meer tonen
Mounting plates GN 900.4 type A are used for installing fixtures on the operator’s side. Type B is used for installing a rotary table GN 900.6. The mounting plate can be simply...Meer tonen
Fastening units GN 900.1 are fitted to the base of the adjustable slide units GN 900 from the operator’s side. The mounting is made on the outside ledge of the slide so that the...Meer tonen
Oil drain valves GN 880 may be used for draining non-pressurised oil. As well conditionally as for vacuum drainage. The flow volume (l/min.) depends on the viscosity of the...Meer tonen
Ball joint heads GN 648.1 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Ball joint heads GN 648.2 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen