The gaskets in types AC and AA correspond to the gaskets DIN 7603, type A (flat gaskets).
The clamping bore of sensor holders GN 277.4 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw location z, the...Meer tonen
Stainless steel washers / Leveling disks GN 6343 are used mainly in mechanical engineering and jigmaking if shimming is required for levelling.
Silicone buffers GN 256 are used as end stops or setup elements for machine and systems, e.g. for conveyors. The silicone rubber used absorbs vibrations, has a damning effect,...Meer tonen
Countersunk washers GN 184.5 are retained to the face of the shaft end with a countersunk head screw DIN ISO 2009 or DIN 7991 forming a clean-look end cap. A typical application...Meer tonen
Slotted locknuts GN 1804.1 are self-locking owing to their polyamide insert. They can therefore also be used as a setting nut and may be used more than once. The thread series...Meer tonen
Stainless steel washers GN 6341 are used mainly in mechanical machine and jig construction when washers DIN 125, DIN 9021 and DIN 6340 no longer meet requirements. In...Meer tonen
Quick release couplings GN 1050 position and connect components without tools using studs GN 1050.1 for a tight and repeatable fit. For repeated machine set ups or assemblies...Meer tonen
Quick-fit couplings GN 240 have been designed for the purpose of compensating a radial off-set x. A typical application is the axial link to a piston rod of a cylinder operating...Meer tonen
Adjustable hand levers GN 303.2 are ideal whenever parts have to be clamped in a confined space or in a particular lever position. The centre insert is connected to the lever...Meer tonen
Adjustable hand levers GN 302 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in a...Meer tonen
Adjustable hand levers GN 302 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in a...Meer tonen
Adjustable hand levers GN 302.1 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in...Meer tonen
Toggle latches GN 761 are especially suited for rapid closing and fastening of covers, container lids and boxes. When the lever is closed, the eccentric configuration of the rod...Meer tonen
Toggle latches GN 832 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Toggle latches GN 832.1are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Toggle latches GN 832.2are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Toggle latches GN 832.3 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Spiralspannhebel GN 9027 spannen z. B. Vorrichtungs- und Maschinenbauteile mit hohen Spannkräften schnell und unabhängig von der Winkelstellung des Spannhebels. Die Steigung der...Meer tonen
Guide rollers GN 753 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. With the radial...Meer tonen
Guide rollers GN 753.1 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. The radial load...Meer tonen
Ball knobs DIN 319 made of steel and aluminum are not on the official DIN standard sheet.
Art.-Nr.
1353714
Leveranciersnummer
839-50-M10-48
EAN
4045525384958
Aantal
1 stuk
Locking pins with axial lock GN 214.2 are used for quick fixing, connecting and locking of various jig and fixture systems. A typical application is location pins which have to...Meer tonen