In addition to the standard travel lengths specified in the above table for the double tube linear actuator GN 492 any length inside the maximum travel length is available. In...Meer tonen
Tube end plugs GN 991 have been designed for sealing tube ends for safety or optical reasons. They are pressed into the tube end either by hand or with a mallet.
The clamping bore of flanged connector clamps GN 147 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...Meer tonen
For mounting clamps, the clamping kits GN 511 replace the socket cap screws with hexagonal socket DIN 912. It is used on all clamping points where repeated clamping actions are...Meer tonen
The clamping bore of swivel clamp connectors GN 276 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw location...Meer tonen
Mounting clampsGN 477 have no thread. Mounting or clamping is made via two threads on the attachment side. The bore distance m corresponds to base plate mounting clamps GN 473,...Meer tonen
The clamping bores of GN 132 two-way connector clamps are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
The clamping bores of two-way connector clamps GN 134 are not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 . The versions with square...Meer tonen
The dimensions of stainless steel retaining rods GN 480.3 are tailored for use with mounting clamps. The angled stainless steel retaining rods make it possible to create compact...Meer tonen
Swivel clamp connector joints GN 281 are an assembly of the swivel clamp connectors GN 271 and GN 275. The clamping bore is mechanically machined and designed for construction...Meer tonen
The clamping bore of base plate connector clamps GN 163 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
The clamping bore of flanged connector clamps GN 146.3 is mechanically machined and designed for construction tubesGN 990 or DIN 2391, DIN 2395 and DIN 2462. Flanged connector...Meer tonen
The clamping bores of two-way connector clamps GN 131 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
The clamping bore of tube supports GN 231 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Tube supports GN 231 can also be mounted...Meer tonen
Angle pieces and shackles GN 967 are preferably used in connection with profile systems. Square connections or connections with same contact area can so be realised in the...Meer tonen
Art.-Nr.
1657869
Leveranciersnummer
7090-28-M4-A-MT-H
EAN
4045525932968
Aantal
1 stuk
Two-Way Mounting Clamps, Plastic
The clamping bore of flanged connector clamps GN 145 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Flanged connector...Meer tonen
The clamping bore of flanged connector clamps GN 146 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
The clamping bores of T-angle connector clamps GN 191 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
In the standard version, the clamping screws are socket cap screws with hexagonal socket DIN 912. They can be replaced by clamping kits GN 511 (article code see table of...
Twistable two-way mounting clamps GN 475 connect rods and tubes within the mounting clamp system under any adjustable angle. With the angle adjustment released, the mounting...Meer tonen
The clamping bores of two-way connector clamps GN 133 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...Meer tonen
In order to be able to utilize the adjustment range of the types with slotted hole for fixing angle pieces GN 561, it is recommended to use mounting screws with a low head, e.g....Meer tonen