The official DIN standard sheet specifies additional sizes 40 - M5 / B5.
Cabinet U-handles GN 425.3 are made of bent stainless steel sections and are affixed by welding. The holes d2 serve, if necessary, for inserting dowel pins or guide pins that...show more
Star knobs GN 6336.1 with bushing have important advantages: The face of the bushing is exactly square to the bore and is with the complete diameter out of steel. The protruding...show more
Latches GN 115 lock by a turning operation limited to 90° which moves the latch arm in the locked position behind the door frame. The bevels of the latch arm ease the closing of...show more
The stroke of the square U-bolts of stainless steel latch type toggle clamps GN 851 can be adjusted within its range. In the clamped position the square U-bolt is parallel to...show more
Edge protection seal profiles GN 2180 can be used to seal doors, covers and hatches. The profiles are pressed by hand onto the front of metal sheets and plates. The embedded...show more
Fork joints GN 751 consist of a fork head according DIN 71752 and a pin with axial shaft safety (Type KL and SL) or a snap-on spring pin (Type B). Size d1 = 12 is supplied with...show more
The retaining magnets GN 51.4 with rubber jacket form a system together with the steel part that shields and strengthens the magnet, optimally concentrating the magnetic flux on...show more
In addition to the standard travel lengths specified in the above table for the double tube linear actuator GN 492 any length inside the maximum travel length is available. In...show more
Stainless Steel Wing Screws
Oil sight glasses GN 743.1 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....show more
Spring plungers GN 616 are used as detents as well as for push-on and push-off applications and ejectors. The slot on the plunger side is provided for blind hole applications. A...show more
Adjustable tension levers GN 212.3 have proved to be ideal whenever parts have to be clamped in a confined space or a particular lever position is re-quired. The threaded insert...show more
Ball lock pins GN 113.8 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...show more
Folding handles GN 425.2 are used in places where the handle must not protrude or protrude only a short distance. In both positions the handle is retained by a spring loaded...
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...show more
Indexing plungers GN 618 without thread are for applications where welding, resin bonding (loctite) or clamping is favoured. Type G has been designed for applications where the...show more
Stainless steel knobs GN 676.5 are used in applica-tions where a push or pull movement is required. Their concave top gives a more comfortable thumb grip. The knurled model...show more
Star knobs with threaded stud GN 5337.13 can be captively attached to a base element with the help of a ball chain. The star knobs with threaded stud are supplied ready...
Hinges GN 128 are produced from drawn weldable profiled steel extrusions. Types ST, STS and MS feature a hinge pin fixed in the lower half of hinge. Type STL with loose steel...show more
Clamping levers with eccentrical cam GN 927 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Tube end plugs GN 991 have been designed for sealing tube ends for safety or optical reasons. They are pressed into the tube end either by hand or with a mallet.
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
Item-no.
1478793
Supplier number
351-30-20-M8-ES-40
EAN
4045525574977
Quantity
1 Piece