The thread locking PRB (polyamide allround coating) is a clamping lock which prevents the locking screw from being inadvertently being loosened and becoming detached.
Threaded plugs DIN 906 are used to close bore holes with cylindrical internal thread. The tightness depends on the medium, pressure, temperature and material pairing. The design...show more
The gaskets in types AC and AA correspond to the gaskets DIN 7603, type A (flat gaskets).
The clamping bore of sensor holders GN 277.4 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw location z, the...show more
Stainless steel washers / Leveling disks GN 6343 are used mainly in mechanical engineering and jigmaking if shimming is required for levelling.
Stainless steel latch type toggle clamps GN 852 are used for very high holding forces as may be required in plastic high pressure mold forming. The stroke of the square U-bolt...show more
Side thrust pins GN 415 have a compact design and offer maximum flexibility for tensioning and holding parts. A variety of thrust pin designs as well as two different spring...show more
Spring loaded side thrust pins GN 715 are versatile and practical elements for holding, positioning and clamping of workpieces. They eliminate costly alternatives, are space...show more
Silicone buffers GN 256 are used as end stops or setup elements for machine and systems, e.g. for conveyors. The silicone rubber used absorbs vibrations, has a damning effect,...show more
Semi-split shaft collars GN 706.2 can safely and simply be assembled by reducing the slot height with high clamping force and thus they act, for instance, like an end stop. The...show more
Slotted locknuts GN 1804.1 are self-locking owing to their polyamide insert. They can therefore also be used as a setting nut and may be used more than once. The thread series...show more
Locking pins with axial lock GN 214.2 are used for quick fixing, connecting and locking of various jig and fixture systems. A typical application is location pins which have to...show more
Locking pins with axial lock GN 114.2 are used for quick fixing, connecting and locking of various jig and fixture systems. A typical application is location pins which have to...show more
Pins with axial lock GN 114.3 are used for quick fixing, connecting and locking of various jig and fixture systems. A typical application is location pins which have to be often...show more
Socket Keys for Latches
Spacer disks and foot disks GN 438 provide a damping and muffling function and protect surfaces from damage. By stacking several spacer disks on each other, the spring rate of...show more
Distance bushings GN 609.5 compensate for the body thread lengths on the indexing plungers and cam action indexing plungers a to allow mounting through walls of varying thickness.
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks to the material used, the spherical washers and dished...show more
Spiralspannhebel GN 9027 spannen z. B. Vorrichtungs- und Maschinenbauteile mit hohen Spannkräften schnell und unabhängig von der Winkelstellung des Spannhebels. Die Steigung der...show more
The handwheels GN 924.7 are suitable for applications where the handle must not remain in the operating position. In order to bring the handle into this position it has to be...show more
With spring latches GN 722.3, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...show more
With spring latches GN 722.3, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...show more
Rastbolzen GN 724.6 verfügen über einen Raststift mit quadratischem Querschnitt und einer Rastfläche, der eine Anlaufschräge gegenüber liegt. Bei einer Bewegung in Richtung der...show more
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended.