The position of linear actuator connectors can be easily read from GN 711 rulers. With GN 711.1 reference arrows, reference points can be marked on rulers or reference positions...show more
Control knobs with adjustable spindle GN 727 allow precise adjustment or aligning i. e. of a positive stop. The spindle thread is without backlash. The graduations on the...show more
Indicator Arrows for Rulers, Plastic/Stainless Steel
Linear slides GN 2402 are also known as linear motion bearings. They are used, for example, for storage drawers and sliding doors, or in jigmaking for a sliding motion in a...show more
Indexing mechanisms GN 200 replace and simplify complicated indexing mechanisms, such as indenting levers, latching mechanisms, indexing pins and other securing elements....show more
Besides the standard scale (coding MCRS) the scale rings can be supplied with any type of graduation. It is suggested to use the matte chrome plated version (MCR) so that a nice...show more
Scale and arrow on the stainless steel control knobs GN 436.1 are indelibly marked and easily legible. Besides the standard scale (type S) the control knobs can be supplied with...show more
Adjustable slide units GN 900 can be combined with a range of adaptors to give various axis configurations. These fastening units and connecting sets (GN 900.1, GN 900.2, GN...show more
With this adjustable knob GN 700 a shaft can be infinitely adjusted in both directions. The anti-backlash mechanism with a max. load of 15 Nm ensures the firm locking of the...show more
Brakes GN 646.5 will reduce the speed of the material conveyed, disrupt or stop the transporting altogether. They are mounted by snapping them into the roller track In type A...show more
Collar Bushings, Accessories for Scaling Sets
Rotary tables GN 900.6 is a turning unit for manual operation. To get the turning movement we use a high quality worm gear. The rotary table is also fitted with a fastadjustment...show more
With connecting sets GN 900.2 two adjustable slide units GN 900 can be combined to produce an X-Y axis configuration. This combination is achieved with a clamping system which...show more
With connecting sets GN 900.3 two adjustable slide units GN 900 can be combined to produce an X-Z axis configuration. The combination is created by using two connection plates...show more
Connectors GN 646.6 (Type C) can be used to create longer carrier profile extensions. Assembled with two screws at each profile end, the carrier profiles are interconnected...show more
Fastening units GN 900.1 are fitted to the base of the adjustable slide units GN 900 from the operator’s side. The mounting is made on the outside ledge of the slide so that the...show more
Bolt sets GN 2290 are designed as accessories for GN 2291 hinge wings for mounting individual hinge versions. Bolt sets with identification no. 1 are designed for hinges with...show more
With indexing levers GN 215 shafts can be turned through a predetermined angle and positively locked. To index, lift the lever against spring pressure from serrations (one hand...show more
The flat springs GN 374 are a perfect and virtually non-wearing connecting link between scale ring GN 264 and spindle or collar bushings GN 268. When adjusting the spindle, they...show more
Indexing mechanisms GN 200 replace and simplify complicated indexing and safety mechanisms. Besides the standard scale (Type AS) the control knob version may be supplied with...show more
Mounting plates GN 900.4 type A are used for installing fixtures on the operator’s side. Type B is used for installing a rotary table GN 900.6. The mounting plate can be simply...show more
Mounting brackets GN 646.7 (Type W) can be used to mount roller rails at a right angle to the support surface, e.g. for the sideways transport of the conveyed material through...show more
Open-End Wrenches
Also this scale rings GN 264 can be supplied with any type of graduation. Regarding design, numbering run, numbering position and numbering sequence of the scale please see the...show more