Winkel GN 30b befestigen Aluprofile z. B. an Tischen und Platten oder rechtwinklig aneinander. Dabei ist keine Bearbeitung des Profils nötig. Die Verbindung lässt sich längs der...show more
Stainless ateel angled ball joints DIN 71802 consist of a ball socket DIN 71805 and a ball shank DIN 71803. The angle of rotation for the type with safety catch (Type CSN) is...show more
Swivel ball joint mounting clamps GN 487 allow precise and stepless adjustment of the ball pivot within the swivel range. This makes it easy to position and adjust components...show more
Mounting clampsGN 477 have no thread. Mounting or clamping is made via two threads on the attachment side. The bore distance m corresponds to base plate mounting clamps GN 473,...show more
DIN 71752 does not foresee size d1= 20.
The clamping bores of two-way connector clamps GN 131 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
The clamping bores of two-way connector clamps GN 133 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
The clamping bores of two-way connector clamps GN 135 are designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The square designs are also suitable for use...show more
In the standard version, the clamping screws are socket cap screws with hexagonal socket DIN 912. They can be replaced by clamping kits GN 511 (article code see table of...
Two-Way Mounting Clamps, Plastic
The clamping bore of flanged connector clamps GN 146 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
The clamping bores of base plate connector clamps GN 163.5 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
The clamping bore of base plate connector clamps GN 165 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...show more
Base plate mounting clamps GN 473 have a horizontal and a vertical clamping bore. The vertical clamping bore is additionally fitted with a square. The bore distance m...show more
Fork joints GN 751.1 basically correspond to the fork head of DIN 71752 (Type A), but, unlike the DIN element, they have a rotating shaft and an additional pin with axial shaft...show more
Fork joints GN 751 consists of a fork head according to DIN 71752 and a pin with one safety circlip DIN 471 (typeA). Standard DIN 71752 does not foresee size d1 = 20.
Item-no.
1213163
Supplier number
751-16-32-M16F-B
EAN
4045525372092
Quantity
1 Piece
Item-no.
1828474
Supplier number
754-12-24-M12-A-ST
EAN
4063632051082
Quantity
1 Piece
Joints pieces GN 752 are designed to be used in combination with fork heads DIN 71752 respectively fork joints GN 751.
The clamping bore of swivel clamp connectors GN 276 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw location...show more
Item-no.
1220815
Supplier number
231-B10-2-BL
EAN
4045525932913
Quantity
1 Piece
The clamping bore of tube supports GN 231 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Tube supports GN 231 can also be mounted...show more
Quick-fit couplings GN 240 have been designed for the purpose of compensating a radial off-set x. A typical application is the axial link to a piston rod of a cylinder operating...show more
Item-no.
1657866
Supplier number
7080-42-M5-A-MT-E
EAN
4045525932739
Quantity
1 Piece