Joints pieces GN 752 are designed to be used in combination with fork heads DIN 71752 respectively fork joints GN 751.
Ball joint heads GN 648.1 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Fork joints GN 751 consist of a fork head according DIN 71752 and a pin with axial shaft safety (Type KL and SL) or a snap-on spring pin (Type B). Size d1 = 12 is supplied with...show more
Ball joint heads GN 648.6 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Stainless ateel angled ball joints DIN 71802 consist of a ball socket DIN 71805 and a ball shank DIN 71803. The angle of rotation for the type with safety catch (Type CSN) is...show more
Item-no.
1394356
Supplier number
784-31-M6-B-1-ELS
EAN
4045525435384
Quantity
1 Piece
Swivel ball joints GN 784 allow precise and stepless adjustment of the ball pivot within the swiveling range. This is a particular advantage when adjusting scanners, cameras,...show more
DIN 71752 does not foresee size d1= 20.
Item-no.
1211893
Supplier number
DIN 71752-4-16-M4
EAN
4045525359345
Quantity
1 Piece
Fork joints GN 751 consists of a fork head according to DIN 71752 and a pin with one safety circlip DIN 471 (typeA). Standard DIN 71752 does not foresee size d1 = 20.
With their smaller dimensions, thin hex nuts GN 909 expand the mounting options of indexing plungers and cam action indexing plungers.
Gaiters GN 808.1 give universal joints full protection against ingress of dirt. At the same time they can be filled with grease which gives long term lubrication for uiniversal...show more
Ball joint heads GN 648.2 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Item-no.
1218404
Supplier number
DIN 908-ST-G11/2-AC
EAN
4045525899612
Quantity
1 Piece
Dust caps GN 710 prevent the entering of dirt into angled ball joints DIN 71802.
Universal joint shafts with friction bearing GN 808.2 not only join the offset between two shafts, but also enable the alignment of lengths, which depending on the overall...show more
Since the moveable parts are not surface treated, i.e. not case hardened, the possibilities of application of these universal joints are much more limited compared to the ones...show more
Universal joints GN 9080 are a simple and very competitively priced variant. They can only be used for applications with low revolutions. Typical applications are all types of...show more
Item-no.
1211994
Supplier number
DIN 71802-10-M6L-CSN
EAN
4045525359857
Quantity
1 Piece
Item-no.
1211999
Supplier number
DIN 71802-13-M8-CN
EAN
4045525359918
Quantity
1 Piece
Item-no.
1212011
Supplier number
DIN 71802-16-M10-CN
EAN
4045525360075
Quantity
1 Piece
Angled ball joints DIN 71802 consist of a ball socket DIN 71805 and a ball shank DIN 71803. The angle of rotation for the type with safety catch (Types CS, BS) ist 15°, without...show more
The clamping nut of the ball joints GN 782 can be set to give a required thrust on the Belleville spring washers in order to increase the resistance to the ball movement. At the...show more
Item-no.
1722641
Supplier number
782-M10-KS-1-NI
EAN
4045525933484
Quantity
1 Piece