Stainless steel welding sockets GN 7490 are used to attach threaded connections to containers, tanks or hydraulic cylinders via welding. Filling and draining screw plugs as well...show more
The stroke of the square U-bolt of latch type toggle clamps GN 851.2 can be adjusted within its range. In the clamped position the square U-bolt and the clamping arm are...show more
Spring plungers GN 615 are used as detents as well as for push-on and push-off applications and ejectors.
Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
With stainless steel hinges GN 127 doors and covers can be positioned snugly and in a finely adjusted manner by moving the adjusting bushings. In this way, door gaps can be...show more
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...show more
Leveling feet GN 439 are used for installing smaller machines, systems or devices. Thanks to the rubber underlay, they have a damping, noise-reducing effect and prevent surface...show more
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
Breather filters GN 882 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The filter function is marked by a blue colour...show more
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...show more
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...show more
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...show more
Clamping bolts GN 918.7 have a circumferential wedge surface. They allow for rapid and secure clamping and releasing with a relatively large clamping range and with high...show more
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Item-no.
1213868
Supplier number
817-10-12-CK-NI-RT
EAN
4045525507333
PU (Packaging)
5 Piece
Quantity
1 Piece
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8, M10 and M12.
The thrust point of the stainless steel grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller...show more
Item-no.
1476819
Supplier number
237.3-NI-80-80-B-GS
EAN
4045525538672
Quantity
1 Piece
Screws GN 1580 are certified according to EHEDG guidelines and are therefore ideal for use in hygienic areas. The sealed mounting surface enables components to be mounted...show more
Stainless steel hex head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. The type with sperical...show more
Item-no.
1076572
Supplier number
DIN 6331-M24
EAN
4045525327153
Quantity
1 Piece