Item-no.
1076405
Supplier number
82032
EAN
4020772082031
Quantity
1 Piece
Item-no.
1076399
Supplier number
82073
EAN
4020772082079
Quantity
1 Piece
Item-no.
1251992
Supplier number
82875
EAN
4020772082871
Quantity
1 Piece
Item-no.
1076766
Supplier number
82925
EAN
4020772082925
Quantity
1 Piece
Item-no.
1076767
Supplier number
82933
EAN
4020772082932
Quantity
1 Piece
Item-no.
1076768
Supplier number
82941
EAN
4020772082949
Quantity
1 Piece
Shaft collars GN 705 essentially comply with the versions of DIN 705. GN 705 also contains a number of practical intermediate sizes in addition to the DIN-versions as well as...show more
The dimensions d2/ l1 of the stainless steel cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2...
Item-no.
1476149
Supplier number
1580-M6-12-MT-E
EAN
4045525583498
Quantity
1 Piece
Setting bolts GN 251 can be used as as a firm end stop as well as for support. The version with Polyurethane disk (type BK) functions as damping element or protection for...
Workholding bolts DIN 6321 are inserted into bores for positioning, assisted by the flattened design (type C) to compensate tolerances in the spacing of two bores. Another...show more
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...show more
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...show more
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8, M10 and M12.
The thrust point of the stainless steel grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller...show more
Item-no.
1476125
Supplier number
1580-M4-12-MT-E
EAN
4045525721371
Quantity
1 Piece
Stainless steel hex head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. The type with sperical...show more
Item-no.
1076572
Supplier number
DIN 6331-M24
EAN
4045525327153
Quantity
1 Piece