Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...show more
High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...show more
With semi-split shaft collars GN 7062.2, e.g., axles are attached to housing, or wheels and washers are installed on shafts. They can be assembled safely and easily with a high...show more
Item-no.
1708196
PU (Packaging)
10 Piece
Quantity
10 Piece
Setting bolts GN 251 can be used as as a firm end stop as well as for support. The version with Polyurethane disk (type BK) functions as damping element or protection for...
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction. The rated load-bearing capacity is shown...show more
Nutensteine GN 50b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Die Feder der Form F sichert den Nutenstein gegen unerwünschtes Verrutschen in der Nut und...show more
T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...show more
Guide rollers GN 753 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. With the radial...show more
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...show more
Slotted locknuts GN 1804.1 are self-locking owing to their polyamide insert. They can therefore also be used as a setting nut and may be used more than once. The thread series...show more
Spherical leveling washers GN 350.3 have been designed to match the leveling sets GN 350, GN 350.1, GN 350.2 and GN 350.5. The two spherical washers are used together...show more
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...show more
Washers DIN 6340 are mainly used for elongated holes. Size 15 is not on the official DIN standard sheet.
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8, M10 and M12.
Stainless steel swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8,...
Grub screws GN 632.1 with ball point are as a rule used with thrust pads GN 631. The ball Ø d2 is smaller than the thread core Ø, which allows fitting over the ball end. The...show more
Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
The thrust point of the grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller than the core...show more
Grub screws GN 913.2 with hardened spherical pivot (type A) are used in such cases where point contact is required. They are a lower cost alternative to ball point screws GN...show more
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Stainless steel hex head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. The type with sperical...show more