Handwheels GN 323.8 have a recessed hub to accept position indicators GN 000.8 / GN 000.3. The hub dimensions (for fitting) correspond to those of disc handwheels GN 323 and/or...
Hinges GN 129 are used for doors which are flush with the frame on the outside. The hinges are normally arranged to the side of the door. In the two-part design, the door can be...Meer tonen
The folding handles with recessed tray GN 425.8 are used if the handle is to protrude by a maximum of 3 mm when folded down. In type A, the folding handle is held in both end...Meer tonen
On slotted locknuts DIN 1804 the ground surface d3 stands proud and should be used as a mating surface. Sizes M45x1,5 to M60x1,5 have 6 slots. The official DIN standard sheet...Meer tonen
Key rings GN 111.3 are suitable as universal connection elements for traction cables, ball chains, retaining straps etc. where light loads are possible. The black design is...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...Meer tonen
Adjustable hand levers GN 603, like all the products of the Ergostyle® range, are renowned for their good style but also their ergonomical shape. They are like all adjustable...Meer tonen
Adjustable hand levers GN 302 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in a...Meer tonen
Toggle latches GN 831.2 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
With extension-tapped holes of the semi-split shaft collars GN 7062.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and...Meer tonen
The thrust point of the stainless steel grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller...Meer tonen
Leveling feet GN 41 are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these leveling feet to be used in...Meer tonen
Leveling feet GN 32 will be delivered mounted and are not removable.
Leveling feet GN 439 are used for installing smaller machines, systems or devices. Thanks to the rubber underlay, they have a damping, noise-reducing effect and prevent surface...Meer tonen
Star Knobs, Cast Iron, Threaded Stud Steel
The star knobs have an immaculate contact or clamping surface thanks to the protruding steel bushing.
The softline coating makes the star knobs with threaded stud GN 5337.6 particularly user-friendly and ergonomic. The soft, slip-proof contact area improves the contact both in...Meer tonen
Star Knobs, Plastic, Bushing Brass
Characteristic of the star knobs GN 5337.4 is the 5 lobes. They not only give the knobs a specific style but this shape has also enabled the operator to achieve a higher torque....Meer tonen
Characteristic of the star knobs GN 5337.7 is the 5 lobes. They not only give the knobs a specific style but this shape has also enabled the operator to achieve a higher torque.
Star knobs GN 6336.2 with all stainless steel bushing (main dimensions of DIN 6336) have important advantages: The face of the bushing is exactly square to the bore and is with...Meer tonen
The influence of a washer on the quality of the screwed connection is very often underestimated. With washers GN 6339, high quality preloaded screwed connections can be...Meer tonen
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction. The rated load-bearing capacity is shown...Meer tonen
T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...Meer tonen