Split hubs GN 150 are distinguished by the method of simple clamping to any shaft. This can be achieved without prior machining of the shaft, eliminating clamping parts and...Meer tonen
Clamping plates GN 9053.6 are used in connection with position indicators GN 9053 and GN 9153. The mounting holes support typical hole patterns. In a simpler way and without...Meer tonen
Clamping plates GN 9054.6 are used in connection with position indicators GN 9054 / GN 9154. The mounting holes support typical bore hole patterns. In a simpler manner and...Meer tonen
Clamping plates GN 953.7 are used in connection with position indicators GN 953 / GN 953.2. The mounting holes support typical bore hole patterns. In a simpler manner and...Meer tonen
Clamping plates GN 955.6 are used in connection with position indicators GN 955 / GN 955.2. The mounting holes support typical bore hole patterns. In a simpler manner and...Meer tonen
The movable bar of the tommy nut DIN 6307 is held in any position by the pressure spring. The plastic end caps limit the travel distance. They are pressed on with form-lock and...Meer tonen
The thrust point of these screws DIN 6306 is designed to be used with or without the thrust pad for clamping. The snap ring is a simple and quick method to connect the thrust...Meer tonen
Art.-Nr.
1724493
Leveranciersnummer
75-16-M6-E-ZB
EAN
4045525892514
Aantal
1 stuk
Mushroom shaped knobs GN 75.6 are intended for use in hygienic areas. The sealed mounting surface enables mounting without dead spaces, the impervious geometry in combination...Meer tonen
Art.-Nr.
1224229
Leveranciersnummer
646.2-270-POM
EAN
4045525999299
Aantal
1 stuk
The design of the ball handles with threaded stud GN 675 matches the product family Ergostyle®. The Softline coating makes the control knobs particularly user-friendly and...Meer tonen
The design of the ball handles GN 675.1 matches the product family Ergostyle®. The softline coating makes the control knobs particularly user-friendly and ergonomic. The soft,...Meer tonen
Art.-Nr.
1216865
Leveranciersnummer
DIN 98-AL-32-D
EAN
4045525418943
Aantal
1 stuk
Art.-Nr.
1216872
Leveranciersnummer
DIN 98-ST-16-D
EAN
4045525419339
Aantal
1 stuk
Art.-Nr.
1343231
Leveranciersnummer
DIN 319-KU-10-M3-C
EAN
4045525235373
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Art.-Nr.
1342651
Leveranciersnummer
DIN 319-KU-40-M12-E
EAN
4045525236233
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Art.-Nr.
1478506
Leveranciersnummer
319-KT-32-M10-E-RT
EAN
4045525721951
Aantal
1 stuk
Art.-Nr.
1478508
Leveranciersnummer
319-KT-40-M10-E-RT
EAN
4045525721968
Aantal
1 stuk
The ball knobs GN 319.1 do not require a thread at the shaft. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place, the shaft end should be...Meer tonen
Art.-Nr.
1478511
Leveranciersnummer
319-KU-25-M5-C-RT
EAN
4045525795259
Aantal
1 stuk
Art.-Nr.
1563487
Leveranciersnummer
319-KU-50-M10-C-RT
EAN
4045525809260
Aantal
1 stuk
Tri-ball handles GN 10 allow fine adjustment. An alternative in modern design are cranked handles GN 510 and control handles GN 112.1.
The unique profile on the rim (small squares) of the knurled screws GN 534 is characteristic of its form and the function.
The unique profile on the rim (small squares) of the knurled knobs GN 534 is characteristic of its form and the function.