The ball end of the grub screw can be hit easily into the thrust pad and removed. The two hex nuts are included parts of the order.
Holders for clamping bolts GN 867 are suitable for use on clamping arms of the power clamps GN 864 / GN 865 / GN 866. Holders for two clamping bolts (type Z) are preferably used...Meer tonen
Static holders GN 867.1 have been designed for use with power clamps GN 864. Static holders with two clamping bolts (Type Z) are preferably used for rigid clamping of sheet...Meer tonen
Thrust pads GN 631 are suitable for universal use and are combined with ball point grub screws GN 632.1. These can be easily pressed into the thrust pad and removed again, if...
Druckstücke GN 631.2 werden zum Spannen und Andrücken verwendet, wenn Oberflächen vor Beschädigung geschützt werden sollen. Darüber hinaus wirken sie rutschhemmend, dämpfend und...Meer tonen
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting connection between the thrust pin and thrust pad, they adapt...Meer tonen
Thrust pads GN 631 are suitable for universal use and are combined with ball point grub screws GN 632.5. These can be easily pressed into the thrust pad and removed again, if...
Art.-Nr.
1208932
Leveranciersnummer
631.5-25-7,8
EAN
4045525739673
Aantal
1 stuk
Stainless steel spring plungers GN 615.5 are used for locking as well as for pressure and hold-off functions. Due to the selection of materials, the stainless steel spring...Meer tonen
Side thrust pins GN 716 are designed for holding, positioning and locating a workpiece. They have to be pressed into the housing by at least the dimension l3, so as to ensure a...
Spring plungers GN 611 are used as ejectors, push-on and push-off operations in the sheet metal industry, as well as cushioners. The slot on the plunger side is provided for...Meer tonen
Art.-Nr.
1208314
Leveranciersnummer
614-10-KD
EAN
4045525312272
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Spring plungers GN 614.2 are a result of a further development of spring plungers type GN 614 for special applications. A tolerance H8 is recommended for the locating bore of d1.
Spring plungers GN 614.3 are used for locking as well as for pressure and hold-off functions. A simple mounting hole is sufficient for mounting. The spring plungers are inserted...Meer tonen
Spring plungers GN 614.6 are primarily used in toolmaking as spring-loaded stops as well as for pressure and hold-off functions. Tolerance d1 H7 is recommended for the mounting...
Spring plungers GN 614.8 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable, which enables...Meer tonen
Spring plungers GN 615.7 are used for end stops as well as contacts. Simultaneously an electrical control signal can be released from the built-in limit switch.
Stainless steel spring plungers GN 615.8 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable,...Meer tonen
Stainless steel spring plungers GN 615.9 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable,...Meer tonen
Stainless steel spring plungers GN 616 are used as detents as well as for push-on and push-off applications and ejectors. The slot on the plunger side is provided for blind hole...Meer tonen
Art.-Nr.
1208474
Leveranciersnummer
616-M12-SS
EAN
4045525314726
VPE (Verpakking)
10 stuk
Aantal
1 stuk
Art.-Nr.
1208482
Leveranciersnummer
616-M4-K
EAN
4045525314849
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Art.-Nr.
1208488
Leveranciersnummer
616-M5-SS
EAN
4045525314924
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Spring plungers GN 616.1 are used for locking as well as for pressure and hold-off functions. Entry of liquids and dirt is prevented by the seal. The slit on the plunger side is...Meer tonen