Art.-Nr.
1076408
Leveranciersnummer
81869
EAN
4020772081867
Aantal
1 stuk
Art.-Nr.
1076401
Leveranciersnummer
81992
EAN
4020772081997
Aantal
1 stuk
Art.-Nr.
1076403
Leveranciersnummer
82016
EAN
4020772082017
Aantal
1 stuk
Art.-Nr.
1076405
Leveranciersnummer
82032
EAN
4020772082031
Aantal
1 stuk
Art.-Nr.
1076399
Leveranciersnummer
82073
EAN
4020772082079
Aantal
1 stuk
Art.-Nr.
1591594
Aantal
1 stuk
Shaft collars GN 705 essentially comply with the versions of DIN 705. GN 705 also contains a number of practical intermediate sizes in addition to the DIN-versions as well as...Meer tonen
Spacers GN 6220 are commonly used as spacing rods. They allow parts to be fastened with an offset parallel to their mounting plane. Type A is also used as a connecting nut. Any...Meer tonen
High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
The dimensions d2/ l1 of the stainless steel cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2...
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...Meer tonen
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
Workholding bolts DIN 6321 are inserted into bores for positioning, assisted by the flattened design (type C) to compensate tolerances in the spacing of two bores. Another...Meer tonen
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
Studs DIN 6379 are primarily used with T-nuts DIN 508. Complete clamping screws can be created by combining them with hexagon nuts DIN 6330 and washers DIN 6340. The official...Meer tonen
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction. They offer a high load carrying capacity and...Meer tonen
Art.-Nr.
1476125
Leveranciersnummer
1580-M4-12-MT-E
EAN
4045525721371
Aantal
1 stuk
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...Meer tonen
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...Meer tonen
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...Meer tonen
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...Meer tonen
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....Meer tonen
T-nuts DIN 508 without thread can be adapted for special applications.