Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...Meer tonen
Hammerkopfmuttern GN 51b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...Meer tonen
Art.-Nr.
1476143
Leveranciersnummer
1580-M5-16-MT-E
EAN
4045525583412
Aantal
1 stuk
Semi-split shaft collars GN 706.4 can safely and simply be clamped by reducing the slot height by using an adjustable hand lever and thus they act, for instance, like an end...Meer tonen
Art.-Nr.
1351846
Leveranciersnummer
653.2-M6-24-NI
EAN
4045525106338
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Stainless steel knurled screws GN 653.2 can be used for to prevent loss of the thumb screw, due to the d4 recessed portion of the stud. When using, instead of a typical tapped...Meer tonen
Clamp spring washers GN 509.3, type A allow ball transfers units to be mounted and removed from the installation side. Retaining rings GN 509.3, type B are mounted from the...Meer tonen
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...Meer tonen
Art.-Nr.
1218728
Leveranciersnummer
1130-8-10-ST
EAN
4045525914148
Aantal
1 stuk
Art.-Nr.
1211327
Leveranciersnummer
705-18-E-ZB
EAN
4045525828391
VPE (Verpakking)
10 stuk
Aantal
1 stuk
Split shaft collars GN 707.5 can be assembled radially, e.g., on cables, shafts and axles as an end stop. The clamping is done by reducing the slot height, wherein the surface...Meer tonen
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
Retaining magnets GN 5090 are designed for use in hygienic areas. The sealed screw-on surface enables mounting without dead spaces, the impervious geometry in combination with...Meer tonen
Stainless steel T-nuts DIN 508 are also available without thread. They can be adapted for special applications in this way.
Trapezgewindemuttern GN 103.2 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Die Schlüsselflächen dienen dabei der Befestigung und verhindern das Mitdrehen der...Meer tonen
Trapezgewindemuttern GN 103.3 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Je nach Werkstoff und der daraus resultierenden Festigkeit werden die Muttern in...Meer tonen
Assembly tools GN 355.1 serve to adjust leveling elements GN 355 / GN 355.2. They are used in connection with a T-wrench or a hexagonal angle socket spanner. To ease leveling,...Meer tonen
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...Meer tonen
Rhombus T-nuts GN 508.1 can be inserted vertically into the T-slot.
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
The official standard sheet of T-slot bolts DIN 787 also lists the sizes 5, 36, 42, 48 and 54.