The retaining magnets GN 51.3 with rubber jacket form a system together with the steel part that shields and strengthens the magnet, optimally concentrating the magnetic flux on...show more
Stainless steel indexing plungers GN 817.4 are similar to GN 817, but with a T-handle instead of a round head. This shape allows better visual orientation of the indexing...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
Indicator Arrows for Rulers, Plastic/Stainless Steel
Carabiners GN 5299 are used, for example, to connect tools or other components quickly and without tools or to secure them against loss. The carabiner is opened by hand and...show more
Going beyond the DIN standard, handwheels DIN 950 are also available with Ø d1 = 180 and in types F and D with fixed or revolving handle.
The static load of the leveling feet GN GN 343.6 is limited by the load capacity of the ball joint / threaded stud (AISI 303). The static load values in the above table refer to...show more
Retaining magnets GN 50.45 are combined with a stainless steel housing and a plastic ring / insulation ring into a system that shields and strengthens the magnet for optimal...show more
Item-no.
1210342
Supplier number
638-18-M8-35-ST
EAN
4045525471771
Quantity
1 Piece
Leveling feet GN 31 with vulcanised rubber (Types B3, B4, C3 and C4) and screw version W feature fewer dead spots owing to their construction method and are also easier to...show more
Leveling feet GN 32 will be delivered mounted and are not removable.
The installation of cabinet U-handles GN 728.5 can be carried out from the back (Type A) as well as from the operator’s side (Type B).
Item-no.
1150620
Supplier number
351-25-30-M6-ES-55
EAN
4045525596023
Quantity
1 Piece
Item-no.
1201069
Supplier number
351-50-30-M10-ES-55
EAN
4045525596108
Quantity
1 Piece
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...show more
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...show more
The folding handles with recessed tray GN 425.8 are used if the handle is to protrude by a maximum of 3 mm when folded down. In type A, the folding handle is held in both end...show more
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...show more
Item-no.
1353719
Supplier number
839-50-M12-98
EAN
4045525385009
Quantity
1 Piece
Rubber buffers GN 356 provide elastic support for equipment such as compressors and pumps. The tapered shape absorbs side forces better compared with cylindrical rubber buffers....show more
Item-no.
1484068
Supplier number
5337.2-25-M5-40
EAN
4045525669833
Quantity
1 Piece
Adjustable hand levers GN 911 replace the socket cap screws DIN 912 of the tube clamp connectors and linear actuator connectors. The table of dimensions of the tube clamp...show more
The breather filters GN 884 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The stainless steel wire mesh prevents...show more
Construction tubes GN 990 can be supplied in these standard lengths. The tolerances specified for the outside diameter of the round construction tubes comply with the...show more