Hinges GN 128 are produced from drawn weldable profiled steel extrusions. Types ST, STS and MS feature a hinge pin fixed in the lower half of hinge. Type STL with loose steel...show more
Retaining magnets GN 50.25 are combined with the stainless steel housing and the plastic ring into a system that shields and strengthens the magnet for optimal transmission of...show more
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...show more
The clamping bore of flanged connector clamps GN 145 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Flanged connector...show more
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...show more
Retaining magnets GN 50.45 are combined with a stainless steel housing and a plastic ring / insulation ring into a system that shields and strengthens the magnet for optimal...show more
The retaining magnets GN 51.3 with rubber jacket form a system together with the steel part that shields and strengthens the magnet, optimally concentrating the magnetic flux on...show more
Item-no.
1210342
Supplier number
638-18-M8-35-ST
EAN
4045525471771
Quantity
1 Piece
Mini indexing plungers GN 822 are distinguished for their small dimensions. They have been designed for installation in thin walled sheet metal constructions. In type C, the...show more
Rubber buffers GN 356 provide elastic support for equipment such as compressors and pumps. The tapered shape absorbs side forces better compared with cylindrical rubber buffers....show more
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...show more
The folding handles with recessed tray GN 425.8 are used if the handle is to protrude by a maximum of 3 mm when folded down. In type A, the folding handle is held in both end...show more
Hinges GN 128.2 are produced from drawn weldable profiled stainless steel extrusions. The pin is fixed in the lower half.
When flow indicators GN 655 are used, a rotor rotates above a minimum volume flow rate Q, depending on the medium and its viscosity. The flow rate is visible from all sides....show more
Hinges GN 1366 are made of rolled or drawn steel profiles and are very robust. Types A and S are fastened by welding or using holes created by the customer. Type S also has a...show more
Adjustable hand levers GN 911 replace the socket cap screws DIN 912 of the tube clamp connectors and linear actuator connectors. The table of dimensions of the tube clamp...show more
The breather filters GN 884 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The stainless steel wire mesh prevents...show more
Construction tubes GN 990 can be supplied in these standard lengths. The tolerances specified for the outside diameter of the round construction tubes comply with the...show more
When ball knobs DIN 319 type L and M are used the shaft does not require a thread. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place,...show more
Revolving ball knobs GN 319.2 are in general used where a pulling action is involved such as on vertically positioned handwheels.
Cabinet U-handles GN 425 are manufactured from a bent stainless steel profile. Cabinet U-handles with Ø d1 = 6, 8 and 10 are delivered with two location disks to ensure proper...show more
Item-no.
1201252
Supplier number
352-30-20-M8-S-55
EAN
4045525597228
Quantity
1 Piece
Stainless steel tension levers GN 212 are used as clamping element as well as operating levers.
The clamping bores of two-way connector clamps GN 134 are not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 . The versions with square...show more