Square U-Bolts, Steel
Stainless Steel-Quick release knurled nuts GN 6303.1 are used in such applications where the nut has to be completely removed after the releasing operation and re-fitted rapidly...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
The outstanding feature of revolving handles GN 598.2 is their highly robust design. Type E is suitable for use in connection with user-specific threaded bolts.
The rotary clamping latches GN 516 have a closing mechanism which transfers the rotary movement of the operating element resp. socket key into a 90° turn and then into a 6 mm...show more
Rubber buffers GN 356 provide elastic support for equipment such as compressors and pumps. The tapered shape absorbs side forces better compared with cylindrical rubber buffers....show more
The handle in the handwheels GN 521.6 is locked in a conical bore in the operating position. For reversal, it must first be pulled from the cone in axial direction. A pressure...show more
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...show more
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....show more
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...show more
The stroke of the square U-bolts of latch type toggle clamps GN 851 can be adjusted within its range. In the clamped position the square U-bolt is parallel to the fixing plane...show more
Side thrust pins GN 714 are the result of further development of GN 715. It is left to the customer to design his own pressure pin which can be screwed into the thrust plate....show more
Spring loaded side thrust pins GN 715 are versatile and practical elements for holding, positioning and clamping of workpieces. They eliminate costly alternatives, are space...show more
With extension-tapped holes of the semi-split shaft collars GN 7062.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and...show more
On slotted locknuts DIN 1804 the ground surface d3 stands proud and should be used as a mating surface. Sizes M45x1,5 to M60x1,5 have 6 slots. The official DIN standard sheet...show more
Spacers GN 6220 are commonly used as spacing rods. They allow parts to be fastened with an offset parallel to their mounting plane. Type A is also used as a connecting nut. Any...show more
With spring latches GN 722.2, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...show more
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
Spring plungers GN 615 are used as detents as well as for push-on and push-off applications and ejectors.
Characteristic of the star knobs GN 5337.4 is the 5 lobes. They not only give the knobs a specific style but this shape has also enabled the operator to achieve a higher torque....show more
Characteristic of the star knobs GN 5337.7 is the 5 lobes. They not only give the knobs a specific style but this shape has also enabled the operator to achieve a higher torque.
Star knobs GN 6336.2 with all stainless steel bushing (main dimensions of DIN 6336) have important advantages: The face of the bushing is exactly square to the bore and is with...show more