Oil sight glasses GN 743 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....show more
Rubber buffers GN 456 provide elastic support for equipment such as compressors and pumps. The tapered shape absorbs side forces better compared with cylindrical rubber buffers....show more
The stroke of the square U-bolts of latch type toggle clamps GN 851.1 can be adjusted within its range. In the clamped position the square U-bolt is perpendicular to the...show more
Characteristic of the star knobs GN 5337.2 is the 5 lobes. They not only give the knobs a specific style but this shape has also enabled the operator to achieve a higher torque.
Toggle latches GN 832 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...show more
Angle pieces and shackles GN 967 are preferably used in connection with profile systems. Square connections or connections with same contact area can so be realised in the...show more
Adjustable tension levers GN 213.3 have proved to be ideal whenever parts have to be clamped in a confined space or a particular lever position is required. The threaded insert...show more
Adjustable hand levers GN 302.2 have a straight lever, not inclined, being parallel to the clamping space. Adjustable hand levers are ideal whenever parts have to be clamped in...show more
Adjustable hand levers GN 500 besides their good design, offer the advantage that the plastic material used is fully penetrated by the colour and will not show any discolouring...show more
Flat adjustable hand levers GN 600, like all the products of the Ergostyle® range, are renowned for their good style but also their ergonomical shape. They are like all...show more
Control knobs with adjustable spindle GN 727 allow precise adjustment or aligning i. e. of a positive stop. The spindle thread is without backlash. The graduations on the...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
The clamping bores of T-angle connector clamps GN 191 are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Winkel GN 30b befestigen Aluprofile z. B. an Tischen und Platten oder rechtwinklig aneinander. Dabei ist keine Bearbeitung des Profils nötig. Die Verbindung lässt sich längs der...show more
Stainless ateel angled ball joints DIN 71802 consist of a ball socket DIN 71805 and a ball shank DIN 71803. The angle of rotation for the type with safety catch (Type CSN) is...show more
The official DIN standard sheet specifies additional sizes 200 - M24 / B24.
Cabinet U-handles GN 425.1 are manufactured from a bent stainless steel profile. Cabinet U-handles with Ø d1 = 8 and 10 are delivered with two location disks to ensure proper...show more
Leveling feet GN 6311.4 are used for installing and leveling devices and equipment. The pin diameter d3 is smaller than the core diameter of the thread, with the effect that the...show more
The specified load in the above table is a recommendation up to which the damping insert can be permanently subjected. This static load equals a thrust on the area of 0,4 N/mm2,...show more
The static load of the leveling feet GN 343.1 is limited by the load capacity of the ball joint (property class 5.8). The static load values in the table refer to a net vertical...show more
Leveling feet GN 343.4 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more
Leveling feet GN 343.8 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more