Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...show more
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...show more
Item-no.
1481797
Supplier number
7430-M16X1,5-MS
EAN
4045525573093
Quantity
1 Piece
Item-no.
1481811
Supplier number
7430-M26X1,5-A4
EAN
4045525573253
Quantity
1 Piece
Item-no.
1481812
Supplier number
7430-M33X1,5-A4
EAN
4045525573260
Quantity
1 Piece
Control handwheels GN 736 are used for setting operations with low torque. Coarse setting is made by means of the cylindrical handle (fingertip grip) followed by fine setting...show more
Control handwheels GN 735 are used for setting operations with low torque. Coarse setting is made by means of the cylindrical handle (fingertip grip) followed by fine setting...show more
Knurled nuts DIN 467 are suitable for universal use and can be tightened and loosened easily without tools. A nut with thread M12 is also available in addition to the types...
When flow indicators GN 655 are used, a rotor rotates above a minimum volume flow rate Q, depending on the medium and its viscosity. The flow rate is visible from all sides....show more
Wing Screws, Threaded Stud Stainless Steel
The clamping bore of base plate connector clamps GN 162.3 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Base plate...show more
The clamping bore of base plate connector clamps GN 165 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...show more
Foot plates GN 6311.3 are used in connection with screws with pivots (grub screws DIN 6332, tommy screws DIN 6304, DIN 6306) for installing and leveling devices and mechanisms....show more
Item-no.
1469793
Quantity
1 Piece
Fork joints GN 751 consists of a fork head according to DIN 71752 and a pin with one safety circlip DIN 471 (typeA). Standard DIN 71752 does not foresee size d1 = 20.
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
Leveling feet GN 344.2 feature a conductive ESD plastic material (PA) or rubber (NBR) which prevents static charges from building up. The imprint ESD-C on the surface of the...show more
Leveling feet GN 344 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more
Knurled handwheels GN 226 are mainly used instead of star and hand knobs for light adjusting or clamping applications.
Stainless steel grub screws GN 632.5 with ball point are as a rule used with thrust pads GN 631 / GN 631.5. The ball Ø d2 is smaller than the thread core Ø, which allows fitting...show more
Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.