Typical in design are the revolving handles GN 798.1 with their stepped shape consisting of two cylinders giving the operator a better grip.
The cylindrical knobs GN 519.1 do not require a thread at the shaft. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place, the shaft end...show more
When using the cylindrical knobs GN 519, make sure that the threaded pin is not too short. Otherwise the plastic element may break under excessive stress exposure.
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Indexing plungers GN 607 are distinguished for their small dimensions. The extremely low lock nuts GN 909 enlarge the mounting options.
Washers DIN 6340 are mainly used for elongated holes. Size 15 is not on the official DIN standard sheet.
Disk handwheels DIN 3670 have recessed grips at their back. As a rule they are supplied without handle, but the mounting of a handle is possible. The handwheel diameter d1=80...show more
Handwheels GN 9234 are intended for use with linear actuators and are designed as disk or spoked handwheels, depending on their size. The applied torque is transmitted by means...show more
Handwheels GN 323.8 have a recessed hub to accept position indicators GN 000.8 / GN 000.3. The hub dimensions (for fitting) correspond to those of disc handwheels GN 323 and/or...
Disk handwheels GN 323 have recessed grips at their back.
Latches GN 119 lock by a turning operation clockwise (right), which moves the cam latch into the locked position behind the door frame. The latches have a pulling-in range of 10...show more
The underside of the three-lobed knob screws GN 5342 is not recessed, which meets the requirements of a "hygienic" version.
Clamping levers with eccentrical cam GN 927.2 are used for rapid clamping and releasing. Contrary to a clamping operation via a thread, these levers permit torque-free clamping....show more
Stainless steel clamping levers with eccentrical cam GN 927.5 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers...show more
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Stainless steel star knobs GN 5334.13 can be captive-attached to a base element with the help of a ball chain or a retaining cable. The star knobs are supplied ready assembled...show more
Stainless steel captive socket cap screws GN 912.2 can be used to prevent loss of the thumb screw, due to the d3 recessed portion of the stud. Thus the „captivity of the...show more
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...show more
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...show more