Holders for spring plungers GN 614.1 are standard parts which simplify the use of spring plungers GN 614. Types R, L and B consist only of the holder for spring plungers...show more
By means of the retaining ring in the thrust pad a simple and toggle link between screw and thrust pad is created. The two hexagon nuts are included parts of the order.
Protective caps GN 806 can be used with hexagon screws ISO 4017 or together with threaded pins type B as thrust pins with soft clamping head surface, or as soft end stop bolts....show more
Square U-Bolts, Stainless Steel
Square U-Bolts, Steel
Push-pull type toggle clamps GN 842 can be used for very high holding capacities thanks to their massive and sturdy body. On the size 70, the mounting holes are provided with...show more
Push-pull type toggle clamps GN 843.1 can be mounted on a mounting bracket (type ASW) or „directly“ on the jig. The center bushing securing method allows the operating handle to...show more
Indexing plungers GN 817.6 with sensor for position monitoring allow for electronic monitoring of the plunger pin state. For this purpose, a magnet is integrated into the...show more
Ball buttons GN 249.1 are mainly used with spring plungers when low wear and exact positioning are needed. To achieve optimal locking of the spring plungers, the maximum...show more
Mounting blocks GN 612.1 simplify the mounting of indexing plungers (e.g. GN 817) as well as cam action indexing plungers GN 612, GN 712 and GN 712.1. To position the indexing...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
The rotary clamping latches GN 516 have a closing mechanism which transfers the rotary movement of the operating element resp. socket key into a 90° turn and then into a 6 mm...show more
The official standard sheet of T-slot bolts DIN 787 also lists the sizes 5, 36, 42, 48 and 54.
Verschlussschrauben DIN 910 werden beispielsweise an Einfüll-, Ablass- oder Kontrollöffnungen von Getrieben oder Hydrauliktanks eingesetzt.
Split shaft collars GN 707.5 can be assembled radially, e.g., on cables, shafts and axles as an end stop. The clamping is done by reducing the slot height, wherein the surface...show more
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....show more
With split shaft collars GN 7072.2, e.g., axles are attached to housing, or wheels and washers are installed on shafts. They can be assembled safely and easily with a high...show more
The draw hook of the latch type toggle clamps GN 850 can be adjusted within the stroke.
The stroke of the square U-bolts of latch type toggle clamps GN 851.1 can be adjusted within its range. In the clamped position the square U-bolt is perpendicular to the...show more
Side thrust pins GN 714 are the result of further development of GN 715. It is left to the customer to design his own pressure pin which can be screwed into the thrust plate....show more
Semi-split shaft collars GN 706.2 can safely and simply be assembled by reducing the slot height with high clamping force and thus they act, for instance, like an end stop. The...show more
On stainless steel slotted locknuts DIN 1804 the ground surface d3 stands proud and should be used as a mating surface. The sizes M45x1,5 to M60x1,5 have 6 slots. The official...show more
Slotted locknuts DIN 70852 serve for adjusting the amount of play or for securing shaft-hub connections in an axial direction, for example. The flat design of the slotted...show more
Slotted locknuts GN 1804.1 are self-locking owing to their polyamide insert. They can therefore also be used as a setting nut and may be used more than once. The thread series...show more