Swing clamps GN 875 are used when the clamping point for inserting and removing the workpiece must be freely accessible on top. During the clamping action, the arm is first...show more
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction. They offer a high load carrying capacity and...show more
Item-no.
1076412
Supplier number
81901
EAN
4020772081904
Quantity
1 Piece
Item-no.
1076407
Supplier number
81950
EAN
4020772081959
Quantity
0 Piece
Spannriemen GN 1110 werden in verschiedenen Bereichen zum Befestigen, Fixieren und Spannen von Bauteilen verwendet.
Clamping bolts GN 918.2 have a circumferential wedge surface. They allow for rapid and secure clamping and releasing with a relatively large clamping range and with high...show more
Toggle latches GN 821 are used among others for the secure holding of flaps and container lids. The clamps will lock securely over the centre and are thus vibration proof. The...show more
Toggle latches GN 832.4 are used for the secure holding of flaps, container lids, etc. They lock securely over the center and are thus vibration proof. The components to be...show more
Toggle latches GN 831.2 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Knee lever modules GN 810.12 have the same properties and attributes as the „Longlife“ GN 810.10 / GN 810.11 heavy duty vertical acting toggle clamps: The clamping arms are...show more
Guide rollers GN 753 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. With the radial...show more
Guide rollers GN 753.1 can be used as guides, bearings or supports for small to medium loads. They can also be used to create custom linear guide rail systems. The radial load...show more
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...show more
Function and operational criteria of breather caps GN 663, see description of function. Breather caps can be connected by either a threaded or a bayonet (BA) fitting and filler...show more
Latch type toggle clamps GN 852.3 are compact in design and can be used to ensure high holding capacities. When closing the spanner, a safety hook positively locks onto the...show more
Item-no.
1218390
Supplier number
DIN 906-NI-R1/4-GPC
EAN
4045525688513
Quantity
1 Piece
Toggle clamps GN 812.1 work according to the toggle principle, lever and clamping bar move in the same direction. In the clamped position the operating lever is in its vertical...show more
Stainless steel washers GN 6341 are used mainly in mechanical machine and jig construction when washers DIN 125, DIN 9021 and DIN 6340 no longer meet requirements. In...show more
Lifting points GN 589 are distinguished for their very low dimensions. They provide high dynamic and static strength and can be load from any direction with approved safety...show more
Clampimg pads GN 709.8 are also used in jig and fixture construction, for example for clamping workpieces, as movable bearing surface or as stop. The swivel-mounted ball...show more
Toggle clamps GN 810.1 work according to the toggle principle: lever and clamping bar move in the same direction. In the clamped position the operating lever is in its vertical...show more
Clampimg pads GN 709.7 are also used in jig and fixture construction, for example for clamping workpieces, as movable bearing surface or as stop. The swivel-mounted ball...show more
Stainless steel leveling sets GN 350.5 are used for leveling, adjusting and linking operations. The spherical washer allows precise installation of two non parallel planes at a...show more
Levelling sets GN 350.5 are used for levelling, adjusting and linking operations. The spherical washer allows precise installation of two non parallel planes at a required...show more