Item-no.
1476125
Supplier number
1580-M4-12-MT-E
EAN
4045525721371
Quantity
1 Piece
Stainless steel hex head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. The type with sperical...show more
Item-no.
1076572
Supplier number
DIN 6331-M24
EAN
4045525327153
Quantity
1 Piece
The influence of a washer on the quality of the screwed connection is very often underestimated. With washers GN 6339, high quality preloaded screwed connections can be...show more
Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...show more
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....show more
With extension-tapped holes of the semi-split shaft collars GN 7062.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and...show more
On slotted locknuts DIN 1804 the ground surface d3 stands proud and should be used as a mating surface. Sizes M45x1,5 to M60x1,5 have 6 slots. The official DIN standard sheet...show more
Spacers GN 6220 are commonly used as spacing rods. They allow parts to be fastened with an offset parallel to their mounting plane. Type A is also used as a connecting nut. Any...show more
Studs DIN 6379 are primarily used with T-nuts DIN 508. Complete clamping screws can be created by combining them with hexagon nuts DIN 6330 and washers DIN 6340. The official...show more
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction. The rated load-bearing capacity is shown...show more
T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...show more
Assembly tools GN 355.1 serve to adjust leveling elements GN 355 / GN 355.2. They are used in connection with a T-wrench or a hexagonal angle socket spanner. To ease leveling,...show more
Item-no.
1218728
Supplier number
1130-8-10-ST
EAN
4045525914148
Quantity
1 Piece
Ball point screws GN 605 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...show more
Clamp spring washers GN 509.3, type A allow ball transfers units to be mounted and removed from the installation side. Retaining rings GN 509.3, type B are mounted from the...show more
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Stainless steel captive socket cap screws GN 912.2 can be used to prevent loss of the thumb screw, due to the d3 recessed portion of the stud. Thus the „captivity of the...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...show more
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...show more