Shaft collars GN 705 essentially comply with the versions of DIN 705. GN 705 also contains a number of practical...Meer tonen
The thrust point of the grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The...Meer tonen
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage...Meer tonen
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any...Meer tonen
Setting bolts GN 251 can be used as as a firm end stop as well as for support. The version with Polyurethane disk...Meer tonen
Nutensteine GN 50b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Die Feder der Form F sichert den...Meer tonen
Art.-Nr.
1076570
Leveranciersnummer
DIN 6331-M12
EAN
4045525327092
VPE (Verpakking)
10 stuk
Aantal
1 stuk
Art.-Nr.
1076571
Leveranciersnummer
DIN 6331-M20
EAN
4045525327146
Aantal
1 stuk
Workholding bolts GN 6322 are used for positioning in bores, with the ball-type shoulder facilitating the insertion...Meer tonen
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks...Meer tonen
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension...Meer tonen
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be...Meer tonen
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting...Meer tonen
Retaining magnets GN 5090 are designed for use in hygienic areas. The sealed screw-on surface enables mounting...Meer tonen
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger...Meer tonen
Hammerkopfmuttern GN 51b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger...Meer tonen
Art.-Nr.
1218734
Leveranciersnummer
1130-8-35-ST
EAN
4045525914193
Aantal
1 stuk
The dimensions d2/ l1 of the stainless steel cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for...Meer tonen
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN...Meer tonen
Kugelrollen GN 509.7 werden z. B. im Maschinen- und Vorrichtungsbau eingesetzt, um schwere Lasten in jede beliebige...Meer tonen
Trapezgewindemuttern GN 103.3 werden zusammen mit Trapezgewindespindeln GN 103 eingesetzt. Je nach Werkstoff und der...Meer tonen
Art.-Nr.
1723478
Leveranciersnummer
103.3-16X4-LH-1-ST
EAN
4045525948839
Aantal
1 stuk
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is...Meer tonen
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder...Meer tonen