The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...show more
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...show more
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Hammerkopfmuttern GN 51b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Item-no.
1476143
Supplier number
1580-M5-16-MT-E
EAN
4045525583412
Quantity
1 Piece
Item-no.
1132314
Supplier number
DIN 6331-M16
EAN
4045525327122
PU (Packaging)
10 Piece
Quantity
1 Piece
Retaining magnets GN 5090 are designed for use in hygienic areas. The sealed screw-on surface enables mounting without dead spaces, the impervious geometry in combination with...show more
Item-no.
1351846
Supplier number
653.2-M6-24-NI
EAN
4045525106338
PU (Packaging)
25 Piece
Quantity
1 Piece
Stainless steel knurled screws GN 653.2 can be used for to prevent loss of the thumb screw, due to the d4 recessed portion of the stud. When using, instead of a typical tapped...show more
Locking plates GN 187.5 can be installed in combination with locking joint sets GN 187.6 to create locking joints. This allows gear lever handles and retaining tubes or trays...show more
With the aid of serrated locking plates GN 188, standard components can be interlocked and firmly attached in defined angular increments. They are joined by welding. The...show more
Locking joint sets GN 187.6 can be used to combine locking heads GN 187.5 to form locking joints. Thanks to the hexagonal shoulder, which creates a form-locking connection that...show more
Stainless steel T-nuts DIN 508 are also available without thread. They can be adapted for special applications in this way.
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting connection between the thrust pin and thrust pad, they adapt...show more
Protective caps GN 806 can be used with hexagon screws ISO 4017 or together with threaded pins type B as thrust pins with soft clamping head surface, or as soft end stop bolts....show more
Rhombus T-nuts GN 508.1 can be inserted vertically into the T-slot.
The official standard sheet of T-slot bolts DIN 787 also lists the sizes 5, 36, 42, 48 and 54.
Verschlussschrauben DIN 910 werden beispielsweise an Einfüll-, Ablass- oder Kontrollöffnungen von Getrieben oder Hydrauliktanks eingesetzt.
The thread locking PRB (polyamide allround coating) is a clamping lock which prevents the locking screw from being inadvertently being loosened and becoming detached.
Item-no.
1211327
Supplier number
705-18-E-ZB
EAN
4045525828391
PU (Packaging)
10 Piece
Quantity
1 Piece