In order to pass the dead centre point and / or compensate for work piece tolerances when using hand operated toggle clamps, an elastic thrust pad such as GN 708.1 can be used....Meer tonen
Spring plungers GN 615.4 are used as detents as well as for push-on and push-off applications and ejectors.
Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
The clamping bore of flanged connector clamps GN 147 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...Meer tonen
Leveling feet GN 343.7 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
Indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob is rotated by 90°...Meer tonen
Cabinet U-handles GN 426.5 can be mounted from the back (type A) as well as from the operator’s side (type B). In this case the stud is first screwed in from the machine side...Meer tonen
A special characteristic of the cabinet U-handles GN 559 is the thumb rest pad on the front of the leg. At the same time the extended leg offers an open ended version with wide...Meer tonen
Cabinet U-handles GN 425 are manufactured from a bent steel profile. Cabinet U-handles with Ø d1 = 6, 8 and 10 are delivered with two location disks to ensure proper contact of...Meer tonen
Elegant design taking account of ergonomic and hygienic requirements are the outstanding features of spoked handwheels GN 522.5. Owing to the materials used, they are especially...Meer tonen
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...Meer tonen
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...Meer tonen
Retaining magnets GN 50.5 are combined with a steel housing and a plastic ring and the plastic cover into a system that shields and strengthens the magnet for optimal...Meer tonen
Rastbolzen GN 724.4 verfügen über einen Raststift mit quadratischem Querschnitt und einer Rastfläche, der eine Anlaufschräge gegenüber liegt. Bei einer Bewegung in Richtung der...Meer tonen
With indexing plungers GN 722.6, the plunger pin is actuated via the pull ring. This is done either manually, with a cable or by means of an extended pull rod with hook. The ZB...Meer tonen
Knurled nuts DIN 466 are suitable for universal use and can be tightened and loosened easily without tools. A nut with thread M12 is also available in addition to the types...
The dowel bore d5 in the DIN 6303 knurled nut is designed for the use of clamping or notch pins. DIN 6303 knurled nuts with H7 bore and the size M12 are not provided on the...Meer tonen
The knurling of the knurled screws GN 535 allows a use in an environment with hygienic requirements.
Clamping elements GN 826 are normally used in connection with control knobs and smaller handwheels. Spindles can so be clamped gently and easily and without much construction...Meer tonen
Adjustable hand levers GN 300.1 are ideal whenever parts have to be clamped in a confined space or in a particular lever position. The centre insert is connected to the lever...Meer tonen
Adjustable hand levers GN 300.5 with solid stainless steel handle, correspond to applications where „aggressive“ surrounding conditions are given, or where stainless steel...Meer tonen
Revolving ball knobs GN 319.5 are in general used where a "pulling action" is involved such as on vertically positioned handwheels.
Ball knobs DIN 319 are not on the official DIN standard sheet.
Ball Knobs, Plastic with Brass Insert