Cabinet U-handles GN 426.5 can be mounted from the back (type A) as well as from the operator’s side (type B). In this case the stud is first screwed in from the machine side...show more
Cabinet U-handles GN 425 are manufactured from a bent steel profile. Cabinet U-handles with Ø d1 = 6, 8 and 10 are delivered with two location disks to ensure proper contact of...show more
Item-no.
1201183
Supplier number
352-10-10-M4-S-55
EAN
4045525597082
Quantity
1 Piece
Item-no.
1201279
Supplier number
352-40-40-M8-S-55
EAN
4045525597280
Quantity
1 Piece
Item-no.
1201296
Supplier number
352-50-40-M10-S-55
EAN
4045525597310
PU (PU NW)
5 Piece
Quantity
1 Piece
Clamping elements GN 826 are normally used in connection with control knobs and smaller handwheels. Spindles can so be clamped gently and easily and without much construction...show more
Adjustable hand levers GN 300.5 with solid stainless steel handle, correspond to applications where „aggressive“ surrounding conditions are given, or where stainless steel...show more
The clamping bores of GN 132 two-way connector clamps are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Hand Knobs, Cast Iron, Threaded Stud Steel
Indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob is rotated by 90°...show more
Item-no.
1020871
EAN
4045525595354
PU (Packaging)
10 Piece
Quantity
1 Piece
Spring plungers GN 615 are used as detents as well as for push-on and push-off applications and ejectors.
Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
The clamping bore of flanged connector clamps GN 147 is not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. The versions with square...show more
The clamping bore of base plate connector clamps GN 163 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. At the screw...show more
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
The thrust point of the grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller than the core...show more
Item-no.
1200984
Supplier number
351-20-20-M6-EE-40
EAN
4045525599031
Quantity
1 Piece
Item-no.
1348208
Supplier number
351-75-25-M12-ES-55
EAN
4045525029477
Quantity
1 Piece
A special characteristic of the cabinet U-handles GN 559 is the thumb rest pad on the front of the leg. At the same time the extended leg offers an open ended version with wide...show more
Heavy duty hinges GN 237.3 are designed for use under tough conditions and are distinguished by a compact design. The hinge pins are integral and allow the hinges to be used in...show more
Item-no.
1076570
Supplier number
DIN 6331-M12
EAN
4045525327092
PU (Packaging)
10 Piece
Quantity
1 Piece
Item-no.
1076571
Supplier number
DIN 6331-M20
EAN
4045525327146
Quantity
1 Piece