T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...Meer tonen
Square U-Bolts, Steel
Spring plungers GN 615 are used as detents as well as for push-on and push-off applications and ejectors.
With spring latches GN 722.2, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...Meer tonen
Latches GN 515 are identical to standard latches GN 115 except for the extended housing. They are operated with a rotation limited to 90°, which moves the latch arm into the...Meer tonen
Latches GN 115 lock by a turning operation limited to 90° which moves the latch arm in the locked position behind the door frame. The bevels of the latch arm ease the closing of...Meer tonen
Art.-Nr.
1214170
Leveranciersnummer
835-46-M8-16-MT
EAN
4045525673731
Aantal
1 stuk
Filler strainers GN 664 are available with mounting flange for threaded or bayonet (BA) connection. Filler strainers prevent the ingress of coarse impurities during the...Meer tonen
Stainless steel hex head screws GN 933.5 with brass or plastic pivots are used when pressure dents or damage to the clamping surface must be avoided. The type with sperical...Meer tonen
Art.-Nr.
1076572
Leveranciersnummer
DIN 6331-M24
EAN
4045525327153
Aantal
1 stuk
Side thrust pins GN 714 are the result of further development of GN 715. It is left to the customer to design his own pressure pin which can be screwed into the thrust plate....Meer tonen
Spring loaded side thrust pins GN 715 are versatile and practical elements for holding, positioning and clamping of workpieces. They eliminate costly alternatives, are space...Meer tonen
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...Meer tonen
T-nuts DIN 508 without thread can be adapted for special applications.
Oil sight glasses GN 743 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....Meer tonen
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...Meer tonen
The stroke of the square U-bolts of latch type toggle clamps GN 851.1 can be adjusted within its range. In the clamped position the square U-bolt is perpendicular to the...Meer tonen
Toggle latches GN 832 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...Meer tonen
Hinges GN 128.2 are produced from drawn weldable profiled stainless steel extrusions. The pin is fixed in the lower half.
The static load of the leveling feet GN 343.1 is limited by the load capacity of the ball joint (property class 5.8). The static load values in the table refer to a net vertical...Meer tonen
The static load of the leveling feet GN 343.2 is limited by the load capacity of the ball joint / threaded stud (property class 5.8). The static load values in the table refer...Meer tonen
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...Meer tonen
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...Meer tonen