Studs DIN 6379 are primarily used with T-nuts DIN 508. Complete clamping screws can be created by combining them with hexagon nuts DIN 6330 and washers DIN 6340. The official...Meer tonen
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction. They offer a high load carrying capacity and...Meer tonen
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
The PFB patch is a jamming thread locking (Polyamide patch). The coating for Type K or KN (standard spring load) is indicated blue, for Type KS or KSN (high spring load) green....Meer tonen
Clamping levers with eccentrical cam GN 927 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen
Clamping levers with eccentrical cam GN 927.2 are used for rapid clamping and releasing. Contrary to a clamping operation via a thread, these levers permit torque-free clamping....Meer tonen
Indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob is rotated by 90°...Meer tonen
Screws GN 1580 are certified according to EHEDG guidelines and are therefore ideal for use in hygienic areas. The sealed mounting surface enables components to be mounted...Meer tonen
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...Meer tonen
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...Meer tonen
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...Meer tonen
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....Meer tonen
Leveling feet GN 148 are designed for setting up heavy machinery and units with insulation against vibrations. This has a positive impact on the lifetime of machines and...Meer tonen
Stainless steel mini indexing plungers GN 822.9 are distinguished for their small dimensions. The stainless steel mini indexing plungers present an affordable alternative to the...Meer tonen
Latches GN 115.1 have smaller dimensions than standard latches GN 115, making them ideal for applications with limited space or requiring an unobtrusive appearance. They are...Meer tonen
Oil sight glasses GN 743 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....Meer tonen
Owing to the U-rail and the cover, oil level indicators GN 654 are extremely stable and are therefore suitable for great lengths. The fluid level can also be viewed from the...Meer tonen
Art.-Nr.
1294149
VPE (Verpakking)
5 stuk
Aantal
1 stuk
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...Meer tonen
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...Meer tonen
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8, M10 and M12.
Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...Meer tonen
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...Meer tonen