Bushings GN 810.18 are accessory for knee lever modules GN 810.12 / GN 810.13.
Drive the insert bushings GN 992 in by using a soft-head mallet. Their lamellas bridge a production tolerance of the internal diameter or of the internal square of ±0.5 mm,...Meer tonen
The groove on cam action indexing plungers GN 721.1 ensures that the locking pin remains in its withdrawn position. For opposing cam action indexing plungers the left or...Meer tonen
For stainless steel cam action indexing plungers GN 721.6 the indexing plunger pin is withdrawn by turning the lock by 180°. For opposing cam action indexing plungers the left...Meer tonen
Stainless steel bezel disks GN 185 are used for shrouding screw joints when a visually nice finish is required. The purpose of the plastic disks supplied as a standard item on...Meer tonen
Cam Latches, Steel
Latches GN 119 lock by a turning operation clockwise (right), which moves the cam latch into the locked position behind the door frame. The latches have a pulling-in range of 10...Meer tonen
Latches GN 118 have a pulling-in range of 2 mm. They are available as a left and a right version, depending on whether the locking action is left or right.
Studs DIN 6379 are primarily used with T-nuts DIN 508. Complete clamping screws can be created by combining them with hexagon nuts DIN 6330 and washers DIN 6340. The official...Meer tonen
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction. They offer a high load carrying capacity and...Meer tonen
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...Meer tonen
Snap latches GN 449.4 combine the function of a gripping tray with that of a snap latch to provide an easy way to keep doors and covers closed. The mounting hole must be created...Meer tonen
The two hexagon nuts are included parts of the order.
By means of the retaining ring in the thrust pad a simple and toggle link between screw and thrust pad is created. The two hexagon nuts are included parts of the order.
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended.
Spring plungers GN 615.8 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable, which enables...Meer tonen
Spring plungers GN 615.9 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable, which enables...Meer tonen
Spring plungers GN 616 are used as detents as well as for push-on and push-off applications and ejectors. The slot on the plunger side is provided for blind hole applications. A...Meer tonen
Spring plungers GN 614.5 are used as detents as well as for push-on and push-off applications and ejectors. The geometric shape of the plastic housing generates a self-clamping...Meer tonen
Holders for spring plungers GN 614.1 are standard parts which simplify the use of spring plungers GN 614. Types R, L and B consist only of the holder for spring plungers...Meer tonen
Push-pull type toggle clamps GN 842 can be used for very high holding capacities thanks to their massive and sturdy body. On the size 70, the mounting holes are provided with...Meer tonen
Push-pull type toggle clamps GN 843.1 can be mounted on a mounting bracket (type ASW) or „directly“ on the jig. The center bushing securing method allows the operating handle to...Meer tonen
Eccentric bushings GN 715.2 allow side thrust pins GN 715 / GN 714 to be adjusted. These bushings allow the side thrust pin to be precisely adjusted to suit the requirements for...
Clamping levers with eccentrical cam GN 927.2 are used for rapid clamping and releasing. Contrary to a clamping operation via a thread, these levers permit torque-free clamping....Meer tonen