Art.-Nr.
1218734
Leveranciersnummer
1130-8-35-ST
EAN
4045525914193
Aantal
1 stuk
Ball lock pins GN 113.5 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...Meer tonen
Split shaft collars GN 707.5 can be assembled radially, e.g., on cables, shafts and axles as an end stop. The clamping is done by reducing the slot height, wherein the surface...Meer tonen
With extension-tapped holes of the split shaft collars GN 7072.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and axles....Meer tonen
With split shaft collars GN 7072.2, e.g., axles are attached to housing, or wheels and washers are installed on shafts. They can be assembled safely and easily with a high...Meer tonen
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
Stainless steel welding sockets GN 7490 are used to attach threaded connections to containers, tanks or hydraulic cylinders via welding. Filling and draining screw plugs as well...Meer tonen
Magnetic plugs GN 738 attract iron particles which might be suspended in the liquid. To avoid breakage or de-magnetising, round rod magnets are fitted with a plastic distance...Meer tonen
Stainless steel mini indexing plungers GN 822.7 are distinguished for their small dimensions. Based on the principle of the mini indexing plungers GN 822, this model combines...Meer tonen
Mini indexing plungers GN 822.1 are distinguished for their small dimensions. They have been designed for installation in thin walled sheet metal constructions. In type C, the...Meer tonen
Oil drain valves GN 880 may be used for draining non-pressurised oil. As well conditionally as for vacuum drainage. The flow volume (l/min.) depends on the viscosity of the...Meer tonen
Oil sight glasses GN 541 have very high mechanical strength. This allows them to be relatively thin while offering a large viewing window. These oil sight glasses can also be...Meer tonen
Oil sight glasses GN 743 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....Meer tonen
The window of oil sight glasses GN 543.2 is embedded in the body during the injection process and it is therefore absolutely leaktight. The sealing ring is embedded in a radial...Meer tonen
Art.-Nr.
1294149
VPE (Verpakking)
5 stuk
Aantal
1 stuk
ATEX-Breather caps GN 552.6 are suitable for use in an explosion risk environment. They comply with the guidelines (ATEX) 2014/34/EU. MAX-MIN markings can easily be marked on...Meer tonen
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...Meer tonen
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...Meer tonen
Swing bolts GN 1524 offer a longer threaded bolt contrary to DIN 444. For stocking purposes cylinder head shoulder bolts GN 732.1 can be used for the sizes M8, M10 and M12.
Positioning bushings with ramping cone GN 412.3 are used in connection with bolts of indexing plungers. The threads are adapted to the mounting blocks GN 412.1 and GN 612.1.
Guide pins GN 771.1 are used in combination with DIN 172 / DIN 179 guide bushings. The shaft tolerance p6 guarantees a perfect pressfit in a mounting borehole H7. The spigot l3...