Locking pins with axial lock GN 214.6 are used for quick fixing, connecting and locking of various jig and fixture systems. A typical application is location pins which have to...show more
Spacers GN 6220 are commonly used as spacing rods. They allow parts to be fastened with an offset parallel to their mounting plane. Type A is also used as a connecting nut. Any...show more
With spring latches GN 722.2, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...show more
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
Studs DIN 6379 are primarily used with T-nuts DIN 508. Complete clamping screws can be created by combining them with hexagon nuts DIN 6330 and washers DIN 6340. The official...show more
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction. The rated load-bearing capacity is shown...show more
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction. They offer a high load carrying capacity and...show more
T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...show more
Toggle latches GN 831.2 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Latch type toggle clamps GN 851.3 are compact in design and can be used to ensure high holding capacities. When closing the spanner, a safety hook positively locks onto the...show more
Item-no.
1214170
Supplier number
835-46-M8-16-MT
EAN
4045525673731
Quantity
1 Piece
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...show more
Hinges GN 237.1 with horizontally elongated hinge wings are made in a compact and sturdy design. They are used when larger spacings are required for the fastening holes.
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...show more
T-nuts DIN 508 without thread can be adapted for special applications.
Oil sight glasses GN 743 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....show more
The stroke of the square U-bolts of latch type toggle clamps GN 851.1 can be adjusted within its range. In the clamped position the square U-bolt is perpendicular to the...show more
Toggle latches GN 832 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...show more
Once the opening pressure given in the table is exceeded, breather valves GN 881 with gasket will vent into a container and so protect against excessive inside container...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
Breather strainers GN 7403 are used in enclosure and device construction. Inserted into the wall of the enclosure, they ensure pressure equilibrium between the inside of the...show more
Leveling feet GN 6311.4 are used for installing and leveling devices and equipment. The pin diameter d3 is smaller than the core diameter of the thread, with the effect that the...show more
The specified load in the above table is a recommendation up to which the damping insert can be permanently subjected. This static load equals a thrust on the area of 0,4 N/mm2,...show more
The static load of the leveling feet GN 343.1 is limited by the load capacity of the ball joint (property class 5.8). The static load values in the table refer to a net vertical...show more