The two hexagon nuts are included parts of the order.
The static load of the leveling feet GN 343.1 is limited by the load capacity of the ball joint (property class 5.8). The static load values in the table refer to a net vertical...show more
Leveling feet GN 6311.4 are used for installing and leveling devices and equipment. The pin diameter d3 is smaller than the core diameter of the thread, with the effect that the...show more
Item-no.
1347835
Supplier number
343.6-32-M12-80-OS
EAN
4045525026582
PU (Packaging)
4 Piece
Quantity
1 Piece
Item-no.
1218734
Supplier number
1130-8-35-ST
EAN
4045525914193
Quantity
1 Piece
Ball transfer units GN 509 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The diameter...show more
Ball chains GN 111.5 are mainly used in connection with ball lock pins and pins with axial lock. The key rings are supplied unmounted. Both rings have the same Ø d1. The load...show more
Ball point screws GN 606 with full ball (type A) are used in applications where a ball point contact is required. The flat faced moving ball (type B) allows a clamping or...show more
Ball lock pins GN 113.3 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...show more
Ball lock pins GN 113.5 are used for quick fixing, connecting and locking of various parts and workpieces. A typical application is locating pins which have often to be removed...show more
Ball transfer units GN 509.1 are elements which are used in conveyor technology. They allow effortless displacement or rotation of even heavy loads in any direction. The...show more
ATEX-Breather caps GN 552.6 are suitable for use in an explosion risk environment. They comply with the guidelines (ATEX) 2014/34/EU. MAX-MIN markings can easily be marked on...show more
Assembly pins GN 2342 are characterized by their use in diverse applications. Depending on the requirement there are three washer types to choose from, which place the assembly...show more
Bushings GN 810.18 are accessory for knee lever modules GN 810.12 / GN 810.13.
Clamping arm extenders GN 810.17 are accessory for knee lever modules GN 810.12 / GN 810.13.
Clamp spring washers GN 509.3, type A allow ball transfers units to be mounted and removed from the installation side. Retaining rings GN 509.3, type B are mounted from the...show more
Latch type toggle clamps GN 850.1 are especially suited for rapid closing and fastening of lids, flaps and molds. During clamping, the pivoting movement of the clamping lever is...show more
The stroke of the square U-bolt of latch type toggle clamps GN 851.2 can be adjusted within its range. In the clamped position the square U-bolt and the clamping arm are...show more
The dimensions d2/ l1 of the cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2 and hubs with...
Connector pieces GN 880.1 are required when using oil drain valves GN 880. Screwing on the connector piece will activate the valve plate of the oil drain valve, allowing the oil...show more
Cam action indexing plungers GN 712.1 are used in such applications where the plunger pin has to protrude only occasionally. When turning the cam by 90° resp. 120° degrees in...show more
Indexing plungers GN 607.3 have been developed for installation in thin walled equipment. It has to be taken into consideration that, depending on the mounting plate thickness...show more
Item-no.
1211975
Supplier number
717-8-M16X1,5-C-NI
EAN
4045525507111
PU (Packaging)
5 Piece
Quantity
1 Piece
Indexing plungers GN 817.3, together with guide bushings DIN 172 / DIN 179, enable precise positioning. The bushings are used to guide the plunger pin as well as for the...show more