Clamping levers with eccentrical cam GN 927.2 are used for rapid clamping and releasing. Contrary to a clamping operation via a thread, these levers permit torque-free clamping....show more
Clamping levers with eccentrical cam GN 927.4 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Stainless steel clamping levers with eccentrical cam GN 927.5 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers...show more
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The lifting eye bolts GN 581 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as...show more
Retaining rings GN 111.6 can be revolving mounted on the cut-in onto shaft ends or handle. Star knobs, for example, can be secured against loss at the place of use with an...show more
Item-no.
1481797
Supplier number
7430-M16X1,5-MS
EAN
4045525573093
Quantity
1 Piece
Item-no.
1481811
Supplier number
7430-M26X1,5-A4
EAN
4045525573253
Quantity
1 Piece
Item-no.
1481812
Supplier number
7430-M33X1,5-A4
EAN
4045525573260
Quantity
1 Piece
When flow indicators GN 655 are used, a rotor rotates above a minimum volume flow rate Q, depending on the medium and its viscosity. The flow rate is visible from all sides....show more
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
Leveling feet GN 344.2 feature a conductive ESD plastic material (PA) or rubber (NBR) which prevents static charges from building up. The imprint ESD-C on the surface of the...show more
Leveling feet GN 344 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more
Grub screws GN 632.1 with ball point are as a rule used with thrust pads GN 631. The ball Ø d2 is smaller than the thread core Ø, which allows fitting over the ball end. The...show more
Stainless steel grub screws GN 632.5 with ball point are as a rule used with thrust pads GN 631 / GN 631.5. The ball Ø d2 is smaller than the thread core Ø, which allows fitting...show more
Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Handles GN 810.15 are accessory for knee lever modules GN 810.12 / GN 810.13.
Item-no.
1209234
Supplier number
DIN 6331-M10
EAN
4045525327078
PU (Packaging)
10 Piece
Quantity
1 Piece
Item-no.
1132314
Supplier number
DIN 6331-M16
EAN
4045525327122
PU (Packaging)
10 Piece
Quantity
1 Piece
The influence of a washer on the quality of the screwed connection is very often underestimated. With washers GN 6339, high quality preloaded screwed connections can be...show more