C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.
Leveling feet GN 344.2 feature a conductive ESD plastic material (PA) or rubber (NBR) which prevents static charges from building up. The imprint ESD-C on the surface of the...show more
Leveling feet GN 344 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...show more
Grub screws GN 632.1 with ball point are as a rule used with thrust pads GN 631. The ball Ø d2 is smaller than the thread core Ø, which allows fitting over the ball end. The...show more
Stainless steel grub screws GN 632.5 with ball point are as a rule used with thrust pads GN 631 / GN 631.5. The ball Ø d2 is smaller than the thread core Ø, which allows fitting...show more
Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.
Stainless steel grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
The thrust point of the grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller than the core...show more
Hammerkopfschrauben GN 52b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Sie werden an beliebiger Stelle in die Nut des Aluprofils eingebracht und durch eine...show more
Handles GN 810.15 are accessory for knee lever modules GN 810.12 / GN 810.13.
Heavy duty hinges GN 237.3 are designed for use under tough conditions and are distinguished by a compact design. The hinge pins are integral and allow the hinges to be used in...show more
Item-no.
1209234
Supplier number
DIN 6331-M10
EAN
4045525327078
PU (Packaging)
10 Piece
Quantity
1 Piece
Item-no.
1132314
Supplier number
DIN 6331-M16
EAN
4045525327122
PU (Packaging)
10 Piece
Quantity
1 Piece
Item-no.
1076571
Supplier number
DIN 6331-M20
EAN
4045525327146
Quantity
1 Piece
Item-no.
1209222
Supplier number
DIN 6330-M12-B
EAN
4045525326927
PU (Packaging)
10 Piece
Quantity
1 Piece
The influence of a washer on the quality of the screwed connection is very often underestimated. With washers GN 6339, high quality preloaded screwed connections can be...show more
Hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low head. Thanks to...show more
The actuating torque of the hinges GN 233 can be adjusted via a setting screw, allowing doors and flaps to be kept open or partially open or closed. Endurance tests have shown...show more
Hinges GN 122.1 with indexing positions keep the door in the three specified positions without additional mechanism. In indexing position the loosening torque is 1.1 Nm (test...show more
Hinges GN 239.4 with integrated two-way switch are suitable for detecting the status of doors, covers and guards on machines and equipment. Opening the door will activate the...show more
Hinges, Detachable, Zinc Die casting
Hinges GN 158 have a special feature in that they cannot be dismantled from the outside. The assembly is only possible from the inside. The pin is not accessible since it is...show more
Item-no.
1217878
Supplier number
136-ST-40-40-B
EAN
4045525852617
PU (Packaging)
10 Piece
Quantity
1 Piece
Retaining magnets GN 5090 are designed for use in hygienic areas. The sealed screw-on surface enables mounting without dead spaces, the impervious geometry in combination with...show more