Stainless steel indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob...Meer tonen
Indexing plungers GN 417 with flange are mounted parallel to the plungers and are characterized by an especially low height. The mounting hole pattern with slots offers generous...Meer tonen
Cabinet U-handles GN 425 are manufactured from a bent stainless steel profile. Cabinet U-handles with Ø d1 = 6, 8 and 10 are delivered with two location disks to ensure proper...Meer tonen
Gear lever handles GN 310 are highly universal options for movement and operation. Actuation of hydraulic valves and control levers eccentric cams are example uses of these...
Going beyond the DIN standard, handwheels DIN 950 are also available with Ø d1 = 180 and in types F and D with fixed or revolving handle.
Retaining magnets GN 50.3 are combined with the steel housing and the plastic ring into a system that shields and strengthens the magnet for optimal transmission of the magnetic...
Type G or GK of the indexing plungers GN 617 have been designed for applications where the indexing plunger is not operated with the standard knob. The indexing plungers are...Meer tonen
Indexing plungers GN 817.9 have been designed such that special versions of the indexing pins can also be made economically in smaller unit quantities. If required, the indexing...Meer tonen
Revolving ball knobs GN 319.2 are in general used where a pulling action is involved such as on vertically positioned handwheels.
When ball knobs DIN 319 type L and M are used the shaft does not require a thread. During mounting, easy blows with a soft hammer are sufficient to drive the knob into place,...Meer tonen
The clamping bores of two-way connector clamps GN 134 are not machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 . The versions with square...Meer tonen
Drive the stainless steel insert bushings GN 992.5 in by using a soft-head mallet. Their lamellas bridge a production tolerance of the internal diameter or of the internal...Meer tonen
Ball joint heads GN 648.6 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...Meer tonen
Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
Indicator Arrows for Rulers, Plastic/Stainless Steel
Art.-Nr.
1150620
Leveranciersnummer
351-25-30-M6-ES-55
EAN
4045525596023
Aantal
1 stuk
Art.-Nr.
1201069
Leveranciersnummer
351-50-30-M10-ES-55
EAN
4045525596108
Aantal
1 stuk
The position of linear actuator connectors can be easily read from GN 711 rulers. With GN 711.1 reference arrows, reference points can be marked on rulers or reference positions...Meer tonen
The static load of the leveling feet GN GN 343.6 is limited by the load capacity of the ball joint / threaded stud (AISI 303). The static load values in the above table refer to...Meer tonen
Key rings GN 111.3 are suitable as universal connection elements for traction cables, ball chains, retaining straps etc. where light loads are possible. The black design is...Meer tonen
The stroke of the square U-bolts of latch type toggle clamps GN 851 can be adjusted within its range. In the clamped position the square U-bolt is parallel to the fixing plane...Meer tonen
The stroke of the square U-bolts of latch type toggle clamps GN 851.1 can be adjusted within its range. In the clamped position the square U-bolt is perpendicular to the...Meer tonen