Item-no.
1348255
Supplier number
352-60-60-M10-S-70
EAN
4045525030039
Quantity
1 Piece
For mounting clamps, the clamping kits GN 511 replace the socket cap screws with hexagonal socket DIN 912. It is used on all clamping points where repeated clamping actions are...show more
Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
Edge protection profiles GN 2184 are installed on the front edge of metal sheets and plates. They protect the surfaces from damage by sharp edges. The edge finish additionally...show more
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...show more
The following guidelines of lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table: The eye bolt must be of fully screwed in to...show more
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...show more
Retractable handles GN 598.3 are used when the handle should not protrude temporarily for space or safety reasons.
Fork joints GN 751 consist of a fork head according DIN 71752 and a pin with axial shaft safety (Type KL and SL) or a snap-on spring pin (Type B). Size d1 = 12 is supplied with...show more
Cranked Handles, Aluminum
Item-no.
1476819
Supplier number
237.3-NI-80-80-B-GS
EAN
4045525538672
Quantity
1 Piece
Nuts GN 1580 are certified according to EHEDG guidelines and are therefore ideal for use in hygienic areas. The sealed mounting surface enables components to be mounted without...show more
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...show more
With stainless steel hinges GN 127 doors and covers can be positioned snugly and in a finely adjusted manner by moving the adjusting bushings. In this way, door gaps can be...show more
The static load of the leveling feet GN GN 343.6 is limited by the load capacity of the ball joint / threaded stud (AISI 303). The static load values in the above table refer to...show more
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...show more
Leveling feet GN 31 with vulcanised rubber (Types B3, B4, C3 and C4) and screw version W feature fewer dead spots owing to their construction method and are also easier to...show more
Leveling feet GN 40 can be used in a host of combinations of base plates and adjustable spindle versions. The base plate with the rubber underlay protects sensitive surfaces and...show more
Stainless steel cam action indexing plungers GN 612 are used in cases where the locking pin must not protrude all the time. By rotating the lock through 180° the locking pin...show more
Stainless steel indexing plungers GN 817 with rest position (Type C / CK) are used for such applications where the plunger has to stay in its retracted position. To achieve...show more
Cam action indexing plungers GN 612.8 are used in cases where the locking pin must not protrude all the time. By rotating the lock through 180° the locking pin withdraws itself....show more
Indexing plungers GN 7017 are activated through a lever and are characterized by small dimensions. These indexing plungers are universally applicable due to their prevention of...show more
Push-Pull Type Toggle Clamps, Steel, for Push-On Clamping
Quick release star knobs GN 6336.3 are used in such applications where the knob has to be completely removed after the releasing operation and refitted rapidly for re-clamping....show more