Besides the standard scale (Type S) the control knobs GN 626 can be supplied with any type of graduation. Regarding design, numbering run, numbering position and numbering...Meer tonen
The underside of the three-lobed knob screws GN 5342 is not recessed, which meets the requirements of a "hygienic" version.
The two hexagon nuts are included parts of the order.
Thrust pads DIN 6311 are used with grub screws DIN 6332 and tommy screws DIN 6304 or DIN 6306. Due to the pivoting connection between the thrust pin and thrust pad, they adapt...Meer tonen
Spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is recommended.
Spring plungers GN 615.9 are used for locking as well as for pressure and hold-off functions. The ball is mounted in a plastic shell so as to be freely movable, which enables...Meer tonen
Stainless steel spring plungers GN 616 are used as detents as well as for push-on and push-off applications and ejectors. The slot on the plunger side is provided for blind hole...Meer tonen
Art.-Nr.
1208482
Leveranciersnummer
616-M4-K
EAN
4045525314849
VPE (Verpakking)
25 stuk
Aantal
1 stuk
Spring plungers GN 615.4 are used as detents as well as for push-on and push-off applications and ejectors.
Push-pull type toggle clamps GN 840 are known for their extremely low height regardless of the position of the operating handle.
Push-pull type toggle clamps GN 842 can be used for very high holding capacities thanks to their massive and sturdy body. On the size 70, the mounting holes are provided with...Meer tonen
Push-pull type toggle clamps GN 843.1 can be mounted on a mounting bracket (type ASW) or „directly“ on the jig. The center bushing securing method allows the operating handle to...Meer tonen
Hand knobs DIN 6335 with bore H7 are available as GN 6335.1. The size 100 is not on the official DIN standard sheet.
Stainless steel clamping levers with eccentrical cam GN 927.5 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers...Meer tonen
Clamping levers with eccentrical cam GN 927.7 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen
Clamping levers with eccentrical cam GN 926.1 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen
Strainer fittings GN 7405 are suited for assembly into piping systems as upstream or downstream protection devices. Depending on the mesh size, particles carried by liquid or...Meer tonen
Leveling feet GN 6311.4 are used for installing and leveling devices and equipment. The pin diameter d3 is smaller than the core diameter of the thread, with the effect that the...Meer tonen
The specified load in the above table is a recommendation up to which the damping insert can be permanently subjected. This static load equals a thrust on the area of 0,4 N/mm2,...Meer tonen
Leveling feet GN 344 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
Leveling feet GN 343.3 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
Leveling feet GN 343.4 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
Leveling feet GN 343.8 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen