Positioning elements GN 409.1 with threaded stud are designed for use as locating plungers, stops and thrust blocks.
Hinges GN 237 with horizontally elongated hinge wings are made in a compact and sturdy design. They are used when larger spacings are required for the attachment bore holes.
Hinges GN 128 are produced from drawn weldable profiled steel extrusions. Types ST, STS and MS feature a hinge pin fixed in the lower half of hinge. Type STL with loose steel...Meer tonen
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
Stainless steel indexing plungers GN 817.4 are similar to GN 817, but with a T-handle instead of a round head. This shape allows better visual orientation of the indexing...Meer tonen
The PFB patch is a jamming thread locking (Polyamide patch). The coating for Type K or KN (standard spring load) is indicated blue, for Type KS or KSN (high spring load) green....Meer tonen
Push-pull type toggle clamps GN 840 are known for their extremely low height regardless of the position of the operating handle.
Clamping levers with eccentrical cam GN 927 are used for rapid clamping and releasing. Hereby, contrary to a clamping operation via a thread, these levers permit a torque-free...Meer tonen
Leveling feet GN 344.5 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
With the shaft clamping units GN 928, round workpieces from 6 to 125 mm can be rapidly, accurately and economically clamped. The threaded hole d5 can be used for attaching a jig...Meer tonen
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...Meer tonen
The dimensions d2/ l1 of the stainless steel cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2...
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...Meer tonen
Toggle latches GN 832.2are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
Leveling feet GN 41 are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these leveling feet to be used in...Meer tonen
Nutensteine GN 50b befestigen Anbauteile und Zubehör in der Nut von Aluprofilen. Die Feder der Form F sichert den Nutenstein gegen unerwünschtes Verrutschen in der Nut und...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and thus, can be used for numerous different applications, e.g. a securing device and as a connection and fastening...Meer tonen
From thread size G½ upwards, the seal of the plugs GN 548.1 is embedded in a radial undercut. For this reason the seal cannot be extruded when tightening the plug. MAX-MIN lines...Meer tonen
Accessories for threaded plugs GN 745 / GN 745.2.
Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
Stainless steel indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob...Meer tonen
Indexing plungers GN 617.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob is rotated by 90°...Meer tonen
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...Meer tonen
Blechscharniere GN 136 sind in vielen unterschiedlichen Ausführungen erhältlich und eignen sich für leichte bis mittelschwere Anwendungen. Die Form A lässt sich außer durch...Meer tonen