Spring plungers GN 614.4 are used for locking, as pressing and back-off pins, but also as impact dampers. A tolerance of H7 for the location hole of d1 is recommended.
Nuts GN 1580 are certified according to EHEDG guidelines and are therefore ideal for use in hygienic areas. The sealed mounting surface enables components to be mounted without...Meer tonen
Toggle clamps GN 820 work according to the toggle principle: lever and clamping bar move in the opposite direction. They require less space for the clamping action. In the...Meer tonen
The dimensions d2/ l1 of the stainless steel cylinder head shoulder bolts GN 732.1 permit a use as bearing pin for swing bolts DIN 444, swing bolts GN 1524, swing nuts GN 444.2...
Stainless steel welding sockets GN 7490 are used to attach threaded connections to containers, tanks or hydraulic cylinders via welding. Filling and draining screw plugs as well...Meer tonen
Oil sight glasses GN 743.1 offer a sight glass of high stability and scratch proof. The seal is achieved with an O-ring on the periphery and not on the face edge of the glass....Meer tonen
Precision type swing bolts DIN 444 are mainly used for jigs and fixtures. Produced in a precision version as is required in machine and jig construction, the stated tolerances...Meer tonen
Blechscharniere GN 136 sind in vielen unterschiedlichen Ausführungen erhältlich und eignen sich für leichte bis mittelschwere Anwendungen. Die Form A lässt sich außer durch...Meer tonen
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...Meer tonen
Stainless steel ball catches GN 4490 are used, for example, to hold flaps and doors closed that must be opened and closed frequently and easily. The stainless steel version is...Meer tonen
Stainless steel latch type toggle clamps GN 851.3 are compact in design and can be used to ensure high holding capacities. When closing the spanner, a safety hook positively...Meer tonen
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...Meer tonen
With stainless steel hinges GN 127 doors and covers can be positioned snugly and in a finely adjusted manner by moving the adjusting bushings. In this way, door gaps can be...Meer tonen
Art.-Nr.
1476819
Leveranciersnummer
237.3-NI-80-80-B-GS
EAN
4045525538672
Aantal
1 stuk
The static load of the leveling feet GN GN 343.6 is limited by the load capacity of the ball joint / threaded stud (AISI 303). The static load values in the above table refer to...Meer tonen
The stroke of the square U-bolts of latch type toggle clamps GN 851 can be adjusted within its range. In the clamped position the square U-bolt is parallel to the fixing plane...Meer tonen
Leveling feet GN 31 with vulcanised rubber (Types B3, B4, C3 and C4) and screw version W feature fewer dead spots owing to their construction method and are also easier to...Meer tonen
Leveling feet GN 40 can be used in a host of combinations of base plates and adjustable spindle versions. The base plate with the rubber underlay protects sensitive surfaces and...Meer tonen
Stainless steel cam action indexing plungers GN 612 are used in cases where the locking pin must not protrude all the time. By rotating the lock through 180° the locking pin...Meer tonen
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...Meer tonen
The stroke of the square U-bolt of latch type toggle clamps GN 851.2 can be adjusted within its range. In the clamped position the square U-bolt and the clamping arm are...Meer tonen
Spacers GN 6220 are commonly used as spacing rods. They allow parts to be fastened with an offset parallel to their mounting plane. Type A is also used as a connecting nut. Any...Meer tonen
The breather filters GN 884 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The stainless steel wire mesh prevents...Meer tonen
Stainless steel indexing plungers GN 817.4 are similar to GN 817, but with a T-handle instead of a round head. This shape allows better visual orientation of the indexing...Meer tonen